Jump to content
Electronics-Lab.com Community
Sign in to follow this  
bonanz

Led display Digital Voltmeter question

Recommended Posts

You should check the data sheet to see if the chip has the accuracy you need. This is a simple matter of research and you should do this yourself.

MP

Share this post


Link to post
Share on other sites

Hi everyone,

I'm building this Voltmeter together with the supply 30V-3A from the projects.
Now I have some questions about it:

1) How can I supply the voltmeter if i'm using a transfo with only one secundary from    the dc supply? If I put a voltage regulator 7905 behind it, can I messure the output voltage correctly then?

2) If I use the schematic out of the datasheet from the icl7107 i can' t get the correct voltage on my display. I can regulate it to 0 at 0V but I can not get the correct output from a input voltage.

I hope someone can help me out with this,

Greetings Wiggle
 

Share this post


Link to post
Share on other sites

Hi All,

Just looking for some confirmation on a couple of things:

1. I'm looking at running this meter from a wall pack - I assume I still have to regulate the power (i.e. can't just stick a zener in there) as the wall pack may not be regulated;

2. Do I need to do anything to regulate current - that is, if the wall pack is rated 9v 500ma, will the regulator take care of the current?

3. The meter will only be reading +ve voltage, but if I'm going to the trouble of putting it together, I might as well put the -ve supply in as well (protection from wrong connection)...

4. If putting in the -ve supply, should I look at using a 12v wall plug?

Thanks,

Monster  :)

Share this post


Link to post
Share on other sites

Hi everyone,

I'm building this Voltmeter together with the supply 30V-3A from the projects.
Now I have some questions about it:

1) How can I supply the voltmeter if i'm using a transfo with only one secundary from the dc supply? If I put a voltage regulator 7905 behind it, can I messure the output voltage correctly then?

2) If I use the schematic out of the datasheet from the icl7107 i can' t get the correct voltage on my display. I can regulate it to 0 at 0V but I can not get the correct output from a input voltage.

I hope someone can help me out with this,

Greetings Wiggle




Could you please post a drawing or explain a little more?

MP

Share this post


Link to post
Share on other sites

Hi All,

Just looking for some confirmation on a couple of things:

1. I'm looking at running this meter from a wall pack - I assume I still have to regulate the power (i.e. can't just stick a zener in there) as the wall pack may not be regulated;

2. Do I need to do anything to regulate current - that is, if the wall pack is rated 9v 500ma, will the regulator take care of the current?

3. The meter will only be reading +ve voltage, but if I'm going to the trouble of putting it together, I might as well put the -ve supply in as well (protection from wrong connection)...

4. If putting in the -ve supply, should I look at using a 12v wall plug?

Thanks,

Monster :)


You should not have the problem of current limitation needed, but others who have built this circuit have complained about the display numbers being a little unstable without real good regulation on the power supply. I recommmend bypass caps at the very least.

MP

Share this post


Link to post
Share on other sites

Hi guys,

I read through all 17 pages of this thread and almost found what I was looking for. A guy asked how you could convert this voltmeter to read millivolts instead of volts but I think the question got lost in the fray because an answer never came up. I read about shunting for reading higher values but it sounds like this won't work backwards for reading smaller values, am I right?

If that's the case then what would I need to do to get a reading in millivolts instead of volts?

p.s. I'm the newest kind of newbie so thanks for any help!

Share this post


Link to post
Share on other sites

Everybody, Hello!

I'm building power supply from this great community. (looks familiar?)
And yeah, I want to add this meters in my PS.

So, I have 2 questions:
1. As I need only measuring positive voltages, I will use just positive 5V supply.
    And as my meter will be set on 0-200V range (with 0.1 V precision), and as I do
    not need negative sign, can I just remove one 7-seg. display - it would be off
    anyway? Of course, brightness resistor would be bigger.
2. Is original PCB layout OK? I hope that one who made Eagle layout is not angry,
    I appriciate his effort, but I realy dont like boards with askew components.  ::)
    Well, maybe I remove negative voltage generator and make this resistors
    straight.

Thanks, Triple

Share this post


Link to post
Share on other sites

Hi Moderators,

Well, there has ben a lot of inquiry about this voltmeter.

I am truly a Newbie in this field, but can someone PLEASE fix this project so it is an easy project/downoad.

Coupled with the power supply project (30v 2a). it is pretty obvious that ppl want this want this project to complete their unit.

Can someone please supply an updated schem with voltmeter in order to finalise this project. I too have got the eagle version and am waiting confirmation that all is correct.

Share this post


Link to post
Share on other sites

There is no guarantee on any schematic you find on the Internet. That is why there is a discussion area for Q/A of the projects in our project section. Most projects which have a substantial conversation thread will also have a link from the project page. The Eagle version is ok. Also, I am pretty sure corrections in the original project were already made my mixos. This should be clear if you read through the pages of this thread. I uploaded the Eagle version so that members who wanted to make a board had an easier method to do so. As far as your comments about the power supply project, many members have built the original and have had no ill effects. The member who has posted the changes in that forum has not built the device, so I will have to take the word of those who have built it over one who claims to be a theory expert.


MP

Share this post


Link to post
Share on other sites

From a purely analytical standpoint, "the theory expert" does make SOME valid points!! From a practical, "I only have to build one of these, not 10,000...", it probably doesn't matter!!

Share this post


Link to post
Share on other sites

Sure. I just get tired of the scare tactics to newbies....you will fry this if you don't follow my instruction....etc.. but then I get emails from those who have built the originals with no problems, grumbling about what they feel is a false posting on this forum.

Projects Q/A is primarily for those who are actively building these projects. Not for theory statements or overall attempt at re-design in one's head. We have a forum for Theory discussions.
Thanks for your input.

MP

Share this post


Link to post
Share on other sites

Okay this is not a theory discusssion , i have built the ICL7107 voltmeter and is working great , form www.electronics-diy.com , here is the PCB layout and silkscreen. the lines are jumpers

These are the componenets list

VALUE        SHAPE        #    REFDES     

1.0MOhm_5%  R0204R7_5    1    R6         
1N4148      DIO_DO35    3    D1,D2,D3   
10K_LIN      TRIPOT10X5V  1    R2         
10kOhm_5%    R0204R7_5    1    R5         
10nF        MKHCON4A    1    C7         
10uF-POL    ELKO10R5    2    C1,C2       
15kOhm_5%    R0204R7_5    1    R3         
47kOhm_5%    R0204R7_5    1    R4         
100kOhm_5%  R0204R7_5    1    R1         
100nF        MKHCON4A    1    C4         
100pF        KERKO5X4R5  1    C3         
220nF        MKHCON4A    1    C6         
470nF        MKHCON4A    1    C5         
DIPSW4      DIPSW4H      1    JSW1       
ICL7107      DIP40S      1    U1         
ICL7660      DIP8        1    U2         
JUMPER      JUMPER      20  J1,J2,J3,J4,J5,J6,J7,J8,J9,J10,J11,J12,J13,J14,J15,J16,J17,J18,J19,J20
SEVEN_SEG_DECIMAL_COM_A 7SEG8DIP14B  4    U3,U4,U5,U6 
TEST_PT1    PB          4    GND,INneg,INpos,VCC

ICL7107.rar

Share this post


Link to post
Share on other sites

The PCB artwork and layout , sorry for too many jumpers. but the thing is this panel meter was for something else then measuring voltage , i am actually calculating length from it . i will post the full project when it is complete

post-15126-14279142933189_thumb.jpg

post-15126-14279142934123_thumb.jpg

Share this post


Link to post
Share on other sites

Hello

Someone was asking about the board that someone drewup in eagle. i looked at it and almost made it, went so far as to burn the board. I think that it isn't right. looks like the 7 segments are backwards.
Don't know has anybody eles tried it.  I'll post the files so you can look at em.
                                          gogo

ICL7107.zip

Share this post


Link to post
Share on other sites

Hello MP
    I know its a double sided board, what I think I did is burned it upside down.
  I think. I am doing heat transfers so I burned the printed the bottom and mirror the top and then printed. Don't know maybe I should of mirrored the bottom and not the top.  guess I will have to stare at it for awhile

                                          gogo

Share this post


Link to post
Share on other sites

hahaha
      Ya MP thats what I think my problem was to begin with.
    Heres what I come up with. I mirrored the bottom layer and just printed the top.
  seems that works. I printed it out and played with it. Makes since that way.
      time to burn another board.
                      have fun gogo

Share this post


Link to post
Share on other sites

AH BOO WHO :'(
    that way won't work either, makes the L7660 backards. I would use  the original project but Iwant to put a L7660 right board too.
              Oh well back to the drawing board.

Hey MP someware on this said there was a schmatic posted on the eagle web site, I coulde find it. You wouldn't  happen to have a copy of it  ::)
                            have fun gogo

Share this post


Link to post
Share on other sites

Hello
                  MP the eagel pcb you posted don't work unless you drill holes throuth the 7107 to get the 7 segments to place right.    Thanks anyway
                                  back the the org.
                                      have fun gogo

Share this post


Link to post
Share on other sites

Join the conversation

You can post now and register later. If you have an account, sign in now to post with your account.

Guest
Reply to this topic...

×   Pasted as rich text.   Paste as plain text instead

  Only 75 emoji are allowed.

×   Your link has been automatically embedded.   Display as a link instead

×   Your previous content has been restored.   Clear editor

×   You cannot paste images directly. Upload or insert images from URL.

Loading...
Sign in to follow this  

×
×
  • Create New...