crazybuoy Posted September 19, 2010 Report Share Posted September 19, 2010 I want transformerless power supply with 24V 2 Amp and I think any existing cell phone battery adopter can do it for me. I have an DC adopter (5V 250 mA) and want some changes in the circuit to get my desired volt & amp. You can review the circuit of any of your adopter, as most peoples has such a adopters. You may also suggest any other circuit that can provides me transformerless power supply with DC 24V 2 Amp. Quote Link to comment Share on other sites More sharing options...
Hero999 Posted September 19, 2010 Report Share Posted September 19, 2010 You can't boost both the current and the voltage, the 5V 250mA adaptor is rated for 5*0.25 = 1.25W, you want 2*24 = 48W.Buy a higher powered power supply, there's no other way and it won't be transformerless, all mains power supplies have a transformer, even you little phone charger does but it might be a lightweight high frequency transformer inside a switched mode power supply. Quote Link to comment Share on other sites More sharing options...
Stephenah Posted September 21, 2010 Report Share Posted September 21, 2010 Power to bear it? ??? Quote Link to comment Share on other sites More sharing options...
Hero999 Posted September 21, 2010 Report Share Posted September 21, 2010 Power to bear it? ???That doesn't make any sense. What do you mean? Quote Link to comment Share on other sites More sharing options...
crazybuoy Posted September 22, 2010 Author Report Share Posted September 22, 2010 How about to use big resistor to drop the 220v AC to 24v AC then use bridge rectifier to convert it to DC? Quote Link to comment Share on other sites More sharing options...
macbeth Posted September 22, 2010 Report Share Posted September 22, 2010 I need some more information regarding that as I am a new bee.I am interested to know more how to reduce power consumption and the use of the solar energy.Moderator edit:Spam removed Quote Link to comment Share on other sites More sharing options...
Hero999 Posted September 22, 2010 Report Share Posted September 22, 2010 How about to use big resistor to drop the 220v AC to 24v AC then use bridge rectifier to convert it to DC?That's a bad idea for two reasons: the DC side will not be isolated from the mains and the resistor will have to dissipate 392W.A transformer would be a better idea but it's probably too large for what he needs. Quote Link to comment Share on other sites More sharing options...
Kevin Weddle Posted September 24, 2010 Report Share Posted September 24, 2010 I think you can substitute a transformer and rectifier for capacitors and diodes if the power requirements are not high. But it would require many large capacitors and isn't worth the trouble. Generally you would require a transformer, rectifier, and voltage regulator. Quote Link to comment Share on other sites More sharing options...
Hero999 Posted September 26, 2010 Report Share Posted September 26, 2010 I think you can substitute a transformer and rectifier for capacitors and diodes if the power requirements are not high. But it would require many large capacitors and isn't worth the trouble. Generally you would require a transformer, rectifier, and voltage regulator.His power requirements are too high. Transformerless power supplies are only any good for currents up to tens of mA, beyond that, the capacitor becomes as large and expensive as a transformer and they should only be used for fully enclosed circuits as the DC side is not isolated from the mains so needs to be treated with the same safety precautions. Quote Link to comment Share on other sites More sharing options...
simplypowersupply Posted November 26, 2010 Report Share Posted November 26, 2010 If all you need is 24Vdc 2A is it really worth the hassle when you can get something like this: http://www.simplypowersupply.com/DIN-Rail-Power-Supply/RP1045D-24FE-24Vdc-1875A-Output-Din-Rail-Power-Supply-with-Redundant-Rdy-signal.aspxorhttp://www.simplypowersupply.com/Chassis-Mount-Power-Supply/RS-50-24-Meanwell-24Vdc-22A-Chassis-Mount-Power-Supply.aspx Quote Link to comment Share on other sites More sharing options...
Recommended Posts
Join the conversation
You can post now and register later. If you have an account, sign in now to post with your account.