Year: 2018
![NEW Siglent SDS2000X-E series oscilloscopes NEW Siglent SDS2000X-E series oscilloscopes](https://www.electronics-lab.com/wp-content/uploads/2018/12/sds2352x-e2-1024x694.jpg)
NEW Siglent SDS2000X-E series oscilloscopes
Siglent SDS2202X-E 2Ch 200MHz 2 GSa/s Oscilloscope. SIGLENT’s new SDS2000X-E Series Super Phosphor Oscilloscopes are available in two bandwidths; 200 MHz and 350 MHz. They each have a maximum sampling rate of 2 GSa/s and a standard record length of 28 Mpts. The most commonly used...
Continue Reading![LSM6DSO – Always-on Motion-Processing iNEMO inertial measurement unit LSM6DSO – Always-on Motion-Processing iNEMO inertial measurement unit](https://www.electronics-lab.com/wp-content/uploads/2018/12/LSM6DSO.png)
LSM6DSO – Always-on Motion-Processing iNEMO inertial measurement unit
The LSM6DSO is a system-in-package featuring a 3D digital accelerometer and a 3D digital gyroscope boosting performance at 0.55 mA in high-performance mode and enabling always-on low-power features for an optimal motion experience for the consumer. The LSM6DSO supports main OS...
Continue Reading![SMARC-sAL28 module runs Linux With Sensitive GbE ports SMARC-sAL28 module runs Linux With Sensitive GbE ports](https://www.electronics-lab.com/wp-content/uploads/2018/12/kontron_smarcsal28.jpg)
SMARC-sAL28 module runs Linux With Sensitive GbE ports
Kontron has introduced its SMARC-sAL28 module, which operates on Linux on a dual-core Cortex-A72 LS1028 SoC with -40 to 85°C temperature range. It offers up to 5x GbE ports with Time Sensitive Networking. We can see that this marks the first time Kontron has offered a module we have...
Continue Reading![5 Node Raspberry Pi 3 CoM Carrier Board With GbE Switch 5 Node Raspberry Pi 3 CoM Carrier Board With GbE Switch](https://www.electronics-lab.com/wp-content/uploads/2018/12/mininodes_5noderpi3com.jpg)
5 Node Raspberry Pi 3 CoM Carrier Board With GbE Switch
MiniNodes has launched a $259 carrier board for developers seeking to build a mini Arm Cluster. The board supports up to 5x Raspberry Pi Compute Modules 3 modules. The 5 Node Raspberry Pi 3 CoM Carrier Board offers a switched Gigabit Ethernet port to enable networking accessibility to...
Continue Reading![Colour Graphics Library for SD1331 OLED display Colour Graphics Library for SD1331 OLED display](https://www.electronics-lab.com/wp-content/uploads/2018/12/SD1331-OLED.png)
Colour Graphics Library for SD1331 OLED display
David Johnson-Davies published a new project. It is a library for SD1331 OLED display module that can even run on ATtiny85 mcu. This is a small color graphics library for an SPI 96x64 colour OLED display based on an SD1331. It allows you to plot points, lines, filled and open...
Continue Reading![Ultra96 Skin Cancer AI Detection Ultra96 Skin Cancer AI Detection](https://www.electronics-lab.com/wp-content/uploads/2018/12/42902792_320585862037515_5824535528132837376_n-1_D5pKNRx9wt.png.jpg)
Ultra96 Skin Cancer AI Detection
This is an interesting project using Ultra96 SBC and NCS to detect and classify skin cancer. According to the Skin Cancer Foundation, half of the population in United States are diagnosed with some form of skin cancer by age 65. The survival rate for early detection is almost 98%, but...
Continue Reading![Zero BZ1 Arduino Board comes with SD and LiPo charger Zero BZ1 Arduino Board comes with SD and LiPo charger](https://www.electronics-lab.com/wp-content/uploads/2018/12/zero-bz1.png)
Zero BZ1 Arduino Board comes with SD and LiPo charger
One of the most beautiful things about using the Arduino ecosystem is its stackable ideology, where you can easily add new functionality to almost any Arduino board and make the bare metal Arduino board look so powerful. Hackers can decide to add an IoT add-on, SD storage add-on, or...
Continue Reading![DIY Pen/Laser Engraver ESP32 Controller DIY Pen/Laser Engraver ESP32 Controller](https://www.electronics-lab.com/wp-content/uploads/2018/12/20181128_204306-scaled-1024x737.jpg)
DIY Pen/Laser Engraver ESP32 Controller
Buildlog.Net Blog published a new project. It's an ESP32 Controller board used to control X/Y and Z axis of Pen or Laser engraving machines. I have done several pen and laser machines lately, so I decided to create a custom PCB for Grbl_ESP32 for these types of machines. This is a...
Continue Reading