Author: mixos
![Measuring Water Flow Rate and Volume using Arduino and a Flow Sensor Measuring Water Flow Rate and Volume using Arduino and a Flow Sensor](https://www.electronics-lab.com/wp-content/uploads/2020/03/YFS201-Water-Flow-Sensor.jpg)
Measuring Water Flow Rate and Volume using Arduino and a Flow Sensor
Flow rate and volume helps tell the amount of fluid going into, or through a particular vessel. For certain process automation applications, this simple-sounding fluid measurement task is so critical to the success of the project that, failure to get it right, could bring the entire...
Continue Reading![Reflectance based Proximity Sensor using Si1102 Reflectance based Proximity Sensor using Si1102](https://www.electronics-lab.com/wp-content/uploads/2020/03/PIC.jpg)
Reflectance based Proximity Sensor using Si1102
This reflective sensor module is a high-performance 0-5 cm active proximity detector. The sensor can provide a range up to 50cm with higher current infra-red LED and current limit resistor R2, R4 used across IR LED. Because the sensor operates on an absolute reflectance threshold...
Continue Reading![TPS1663 60 V, 6 A Power Limiting eFuse TPS1663 60 V, 6 A Power Limiting eFuse](https://www.electronics-lab.com/wp-content/uploads/2020/03/fbd_slvset9d.gif)
TPS1663 60 V, 6 A Power Limiting eFuse
Texas Instruments' eFuse can be used for hot-swap and power rail protection applications Texas Instruments' TPS1663 is an easy-to-use, positive 60 V, 6 A eFuse with a 31 mΩ integrated FET. Protection for the load, source, and the eFuse itself are provided along with adjustable...
Continue Reading![ADS131M08 8-Channel Simultaneous Sampling Delta-Sigma (ΔΣ) ADC ADS131M08 8-Channel Simultaneous Sampling Delta-Sigma (ΔΣ) ADC](https://www.electronics-lab.com/wp-content/uploads/2020/03/156125908.png)
ADS131M08 8-Channel Simultaneous Sampling Delta-Sigma (ΔΣ) ADC
Texas Instruments' 24-bit, 32 kSPS ADC is optimized for cost-sensitive applications that require simultaneous sampling Texas Instruments' ADS131M08 8-channel, simultaneously-sampling, 24-bit ΔΣ ADC offers wide dynamic range, low power, and energy-measurement-specific features. These...
Continue Reading![IBASE Announce SMARC 2.0 CPU Module with NXP i.MX 8M Mini Processor IBASE Announce SMARC 2.0 CPU Module with NXP i.MX 8M Mini Processor](https://www.electronics-lab.com/wp-content/uploads/2020/02/IBASE-RM-N8MMI-648x330-1.jpg)
IBASE Announce SMARC 2.0 CPU Module with NXP i.MX 8M Mini Processor
IBASE Technology, a manufacturer of application-specific embedded computer platforms, has announced the release of the RM-N8MMI SMARC 2.0 CPU Module built with NXP ARM Cortex-A53 i.MX 8M Mini Quad 1.6GHz industrial-grade processors. Together with a customised carrier board equipped...
Continue Reading![5W USB Type-C Power Delivery 3.0 Adapter Reference Design 5W USB Type-C Power Delivery 3.0 Adapter Reference Design](https://www.electronics-lab.com/wp-content/uploads/2020/02/ST-USB-ref-design.jpg)
5W USB Type-C Power Delivery 3.0 Adapter Reference Design
The EVLSTCH03-45WPD 45W USB Type-C® Power Delivery 3.0 adapter from STMicroelectronics is a USB-IF certified solution and reference design. The EVLSTCH03-45WPD is an isolated ac-dc power supply with a standalone USB PD controller. The board implements at the primary side a...
Continue Reading![PicoScope 6000E 8-Channel 500MHz Mixed-Signal Oscilloscopes PicoScope 6000E 8-Channel 500MHz Mixed-Signal Oscilloscopes](https://www.electronics-lab.com/wp-content/uploads/2020/02/ps6000e-scaled-e1582886570384-1024x625.jpg)
PicoScope 6000E 8-Channel 500MHz Mixed-Signal Oscilloscopes
The PicoScope 6000E series brings very high speed performance to an 8 analog channel, 16 digital channel oscilloscope with 5GSa/s sampling and 4GSa deep memory. Saelig Company, Inc. has introduced the PicoScope 6000E Series 8-channel 500MHz Oscilloscopes, which provide 8 to 12 bits of...
Continue Reading![3DPAS – A 3D printed stand for your Peak Atlas product 3DPAS – A 3D printed stand for your Peak Atlas product](https://www.electronics-lab.com/wp-content/uploads/2020/02/3D-Printed-Peak-Atlas-Stand-Peak-Electronic-Design-Limited-e1582881519748.png)
3DPAS – A 3D printed stand for your Peak Atlas product
Peak Electronic Design Ltd has designed a 3D stand for their popular Peak Atlas Instruments. The stand makes the instrument sit on an angle (30°) view on top of your bench for easy reading and handing. This has been designed by Jez Siddons of Peak Electronic Design Ltd , directly using...
Continue Reading