![Better 3D graphics on the Arduino – ILI9341 LCD Better 3D graphics on the Arduino – ILI9341 LCD](https://www.electronics-lab.com/wp-content/uploads/2016/01/Montage.png)
Better 3D graphics on the Arduino – ILI9341 LCD
M Rule @ crawlingrobotfortress.blogspot.com discuss about ways to optimize 3D rendering on ILI9341 LCD and Arduino: Both optimizing ILI9341 LCD drivers and rendering basic wireframe meshes have been done before. XarkLabs provides an optimized fork of Adafruit's library. Youtube...
Continue Reading![Raspberry Pi Zero Extreme Teardown Raspberry Pi Zero Extreme Teardown](https://www.electronics-lab.com/wp-content/uploads/2016/01/raspberry-pi-zero-extreme-teardo-1024x576.jpg)
Raspberry Pi Zero Extreme Teardown
A very close look at the new Raspberry Pi, include a die-dcap of the SOC (system on chip) and looking at what some of the silkscreen text means Raspberry Pi Zero Extreme Teardown -...
Continue Reading![Building a piCentr home media center Building a piCentr home media center](https://www.electronics-lab.com/wp-content/uploads/2016/01/FDILV6LII3H879T.MEDIUM.jpg)
Building a piCentr home media center
mjrice @ instructables.com shows us how to build a Raspberry Pi home media center. The layout of the enclosure is meant to keep all cabling tidy and inside out of view, with accessible ports for everything you need. A 3D printed internal chassis is part of the design, which holds the...
Continue Reading![Isolated USB-to-UART converter Isolated USB-to-UART converter](https://www.electronics-lab.com/wp-content/uploads/2016/01/DI5499f4.jpg)
Isolated USB-to-UART converter
Jacob Beningo shows how to build an isolated USB to UART converter using Sparkfun's modules. A simple isolation circuit that costs only a few dollars could have been used to protect the USB port on the computer. Embedded system developers get used to plugging strange hardware and...
Continue Reading![Inside the ALU of the first ARM microprocessor Inside the ALU of the first ARM microprocessor](https://www.electronics-lab.com/wp-content/uploads/2016/01/silicon-regions.png)
Inside the ALU of the first ARM microprocessor
Dave @ daveshacks.blogspot.co.uk takes a look inside the first ARM microprocessor and explains it's design. With that in mind I embarked on my own attempt to reverse-engineer parts of the armv1. Some background knowledge of the processor's architecture is helpful, and googling for...
Continue Reading![INA219 current sensor DIY Breakout board INA219 current sensor DIY Breakout board](https://www.electronics-lab.com/wp-content/uploads/2016/01/23577455661_4c48a0beca_z-600x450.jpg)
INA219 current sensor DIY Breakout board
Juan Ignacio has designed a INA219 current sensor DIY Breakout board: Another small board, this time for a INA219. The INA219 is a high-side current shunt and power monitor with an I2C interface. For testing I used Rei VILO library with a MSP430G2553 and Energia, and I measured the...
Continue Reading![Happy New Year Happy New Year](https://www.electronics-lab.com/wp-content/uploads/2016/01/happy-new-year-2016-HD-1024x576.jpg)
Happy New Year
Happy New Year 2016 to all of you. May the new year bring you happiness and...
Continue Reading![UCload new PCB build UCload new PCB build](https://www.electronics-lab.com/wp-content/uploads/2015/12/ucload_rev2a-1080x675-1024x640.jpg)
UCload new PCB build
Sjaak has published a new PCB build, uC controlled dummy load: With no snow outside I finally got around to solder the 3rd PCB. It is the second revision of a microcontroller dummy load. It is loosely based on the arachnidlabs uc:load. It uses the same base ciruit and adds a...
Continue Reading