![PCB stencil jig PCB stencil jig](https://www.electronics-lab.com/wp-content/uploads/2015/09/PCB_stencil_jig.png)
PCB stencil jig
Gonazar’s PCB stencil jig: My solution to making a PCB stencil jig. I need this to do a run of ~30 small boards I got from DirtyPCB who also provided me with the stencil. However, I know that I’m going to be making more later with a new revision so I wanted a jig that I could...
Continue Reading![Can a current flow even up the hill? Can a current flow even up the hill?](https://www.electronics-lab.com/wp-content/uploads/2015/09/obr1755_uvod.jpg)
Can a current flow even up the hill?
Of course it can, even apeak. So if you connect leads from the bottom side via a PCB connector, you don´t have to worry about the current... Should you however be afraid of accidental fall off of the connector (it will certainly hold on if there are no vibrations, shocks or...
Continue Reading![High Speed Ecosystem Support and Calamity Monitoring System High Speed Ecosystem Support and Calamity Monitoring System](https://www.electronics-lab.com/wp-content/uploads/2015/09/ecosystem.png)
High Speed Ecosystem Support and Calamity Monitoring System
The innovation of equipment for calamity detection and monitoring are quite rampant. It is because of consecutive aggression of storms and earthquakes in different parts of the world. As to observe the different scenarios, these are not merely natural causes, there are some or most of...
Continue Reading![18 PIN PIC Development Board 18 PIN PIC Development Board](https://www.electronics-lab.com/wp-content/uploads/2015/09/18PIN-PIC-Development-Board-PIC1.jpg)
18 PIN PIC Development Board
The PIC 18 PIN (DIP) Development / Evaluations Board demonstrates the capabilities of Microchip’s 8-bit microcontrollers, specifically, 18 Pin PIC16F1847. It can be used as a standalone demonstration board with a programmed part. With this board you can develop and prototype with...
Continue Reading![ESP8266 remote controlled sockets ESP8266 remote controlled sockets](https://www.electronics-lab.com/wp-content/uploads/2015/09/thumbnail-remote-controlled-sockets-700-600x336.jpg)
ESP8266 remote controlled sockets
Rui Santos published a new project, an ESP8266 remote controlled sockets: In this project your’re going to build a web server with an ESP8266 that can control remotely any sockets (safely!). ESP8266 remote controlled sockets -...
Continue Reading![Arduino – How to use a Force Sensitive Resistor Arduino – How to use a Force Sensitive Resistor](https://www.electronics-lab.com/wp-content/uploads/2015/09/FIE2TLMIEV84MV8.MEDIUM-e1442994979136.jpg)
Arduino – How to use a Force Sensitive Resistor
by codebender_cc @ instructables.com: In this tutorial you will learn how to use an FSR - Force Sensitive Resistor with Arduino to fade an LED. This sensor is a variable resistor just like a photocell or flex sensor. The resistance changes by applying pressure on it. Arduino - How...
Continue Reading![Laser Diode Driver Laser Diode Driver](https://www.electronics-lab.com/wp-content/uploads/2015/09/LASER-DIODE-DRIVER-PIC1.jpg)
Laser Diode Driver
Laser Diode Driver project will help you safely drive (constant current) a 3 mW visible Laser Diode for your application. Input supply – 2.5 to 6 VDC Onboard preset to adjust the current flow to the Laser Diode Power-On LED indicator Header connector for easy input supply...
Continue Reading![8V97051 Low Power Wideband Fractional RF Synthesizer 8V97051 Low Power Wideband Fractional RF Synthesizer](https://www.electronics-lab.com/wp-content/uploads/2015/09/RF_synthesizer.png)
8V97051 Low Power Wideband Fractional RF Synthesizer
This design features a low power wideband RF synthesizer that is used in GSM receiver cards. It has dual differential and open drain outputs with frequency range of 34.375MHz to 4400MHz(in continuous range). The logic compatibility is 1.8V while the system is running on a single 3.3V...
Continue Reading