![hackaBLE – tiny nRF52832 BLE development board hackaBLE – tiny nRF52832 BLE development board](https://www.electronics-lab.com/wp-content/uploads/2017/11/2017-11-14T08-45-33.686Z-hackaBLE-prog2.jpg)
hackaBLE – tiny nRF52832 BLE development board
Electronut Labs recently released their open source Nordic nRF52832 development board that can be used for your next BLE project. This tiny board can be plugged on a breadboard or soldered on a PCB and provides additional value from just using the BLE module directly as it includes...
Continue Reading![PulseRain M10 – FPGA Development board is Arduino compatible PulseRain M10 – FPGA Development board is Arduino compatible](https://www.electronics-lab.com/wp-content/uploads/2017/11/pre-launch_jpg_project-main.jpg)
PulseRain M10 – FPGA Development board is Arduino compatible
Over the years FPGAs have become readily available to the maker community. They are now more accessible than ever as many development boards has seen the light. It’s now possible to embed a soft-core MCU into an FPGA rather than using a hard-core ASIC MCU and here is where PulseRain...
Continue Reading![IoD-09, An Intelligent WiFi-Enabled Display Module IoD-09, An Intelligent WiFi-Enabled Display Module](https://www.electronics-lab.com/wp-content/uploads/2017/11/iod-09-an-intelligent-wifi-enabl-1024x576.jpg)
IoD-09, An Intelligent WiFi-Enabled Display Module
4D Systems, the manufacturer of intelligent graphics solutions, has announced a new 0.9” smart display module as part of the ‘IoD-09’ series. This series is a set of small full-color TFT display modules that feature the Espressif ESP8266 SoC. It also comes with microSD card slot...
Continue Reading![HeartyPatch – Open source ECG patch with Wifi HeartyPatch – Open source ECG patch with Wifi](https://www.electronics-lab.com/wp-content/uploads/2017/11/heartypatch-product-bothsides_jpg_project-body.jpg)
HeartyPatch – Open source ECG patch with Wifi
An ECG patch with HRV monitoring that's open source, affordable, and Wi-Fi/Bluetooth connected. HeartyPatch is a completely open source, single-lead, ECG-HR wearable patch with HRV (Heart Rate Variability) analysis. It is based on the popular ESP32 system-on-a-chip. By using low-cost,...
Continue Reading![REFLO – Compact, open, and smart PCB reflow oven REFLO – Compact, open, and smart PCB reflow oven](https://www.electronics-lab.com/wp-content/uploads/2017/11/reflo-compact-open-and-smart-pcb.jpg)
REFLO – Compact, open, and smart PCB reflow oven
REFLO is a stylish, portable reflow oven for creators and makers to easily, quickly, and professionally prototype their IoT device, wearable, small robot, etc. REFLO’s features: Portable at only 6” x 6” x 2” - it’s the worlds smallest reflow oven Efficient as it...
Continue Reading![sKan – Low cost and non-invasive melanoma detection device sKan – Low cost and non-invasive melanoma detection device](https://www.electronics-lab.com/wp-content/uploads/2017/11/Screen-Shot-2017-11-08-at-9.48.04-AM-1024x766.png)
sKan – Low cost and non-invasive melanoma detection device
A team of medical and bioengineering undergraduates from McMaster University, Canada have designed a cancer detection device able to detect melanoma. Their design solution, the sKan, is a low cost and non-invasive detection device. Annually, skin cancer accounts for 1 in every 3 cancer...
Continue Reading![2 X AA Battery To 6V Boost Converter For Arduino Nano 2 X AA Battery To 6V Boost Converter For Arduino Nano](https://www.electronics-lab.com/wp-content/uploads/2017/11/003.jpg)
2 X AA Battery To 6V Boost Converter For Arduino Nano
This project is simple solution to power Arduino Nano from two 1.5V batteries. Circuit converts 2 X AA alkaline battery power into 6V 100mA using boost topology. Circuit uses SOT223-6 pin TLV61046A boost converter IC. The TLV61046A is a highly integrated boost converter designed for...
Continue Reading![Programming the ATtiny10 using Arduino IDE Programming the ATtiny10 using Arduino IDE](https://www.electronics-lab.com/wp-content/uploads/2017/11/usbasp-1024x488.jpg)
Programming the ATtiny10 using Arduino IDE
David Johnson-Davies @ technoblogy.com has a nice guide on how to program ATtiny10 6-pin mcu using the arduino IDE. Programming is done using the widely available USBasp programmer from Thomas Fischl. Examples are also included on the guide. Unlike the SPI protocol used to program the...
Continue Reading