![SmartWatering – Arduino plant watering SmartWatering – Arduino plant watering](https://www.electronics-lab.com/wp-content/uploads/2016/07/Prototype-1024x807.jpg)
SmartWatering – Arduino plant watering
Arduino based project in charge of taking care of your green plant. Particle Core based project in charge of taking care of my green plants. The water pump will not work with a voltage under 5V. In order to power it, I soldered a wire straight on the VUSB pin of the USB header....
Continue Reading![Easy Planter – A Simple Way Of Monitoring Plants Easy Planter – A Simple Way Of Monitoring Plants](https://www.electronics-lab.com/wp-content/uploads/2016/07/easyplanter.png)
Easy Planter – A Simple Way Of Monitoring Plants
Easy Planter is a plant monitoring device able to sense temperature, humidity, pressure, moisture, light etc. A small bluetooth low energy plant sensor that easily fits into a plant pot. It can monitor temperature, humidity, pressure, moisture, light, and has I2C extension pins so...
Continue Reading![One Channel Infra Red Remote Controller One Channel Infra Red Remote Controller](https://www.electronics-lab.com/wp-content/uploads/2016/07/H015-500x500-e1555490996562.jpg)
One Channel Infra Red Remote Controller
One Channel Infra-Red Remote and receiver with onboard Relay provides normally open and normally closed output. The project based on PIC12F683 Microcontroller from Microchip , TSOP1738 used as Infra-Red receiver. Micro-controller decodes the RC5 serial data coming from TSOP1738 and...
Continue Reading![Proteus Tutorial – Light Emitting Diode (LED) and Bar Graph Display Proteus Tutorial – Light Emitting Diode (LED) and Bar Graph Display](https://www.electronics-lab.com/wp-content/uploads/2016/07/Selection-of-Edit-Properties-Option-in-Proteus.png)
Proteus Tutorial – Light Emitting Diode (LED) and Bar Graph Display
circuitstoday.com guide us to the basics of LED and bargraph usage in Proteus software. In this post we will be learning on how to use the “Light Emitting Diode (LED)” component in Proteus simulation software. In case you have not got on through the basics of Proteus, here is...
Continue Reading![Maximize the Energy from Long-Life Batteries Maximize the Energy from Long-Life Batteries](https://www.electronics-lab.com/wp-content/uploads/2016/07/article-2016july-maximize-the-energy-from-fig1.jpg)
Maximize the Energy from Long-Life Batteries
by digikey.com: Battery lifetime is a key consideration for the development of the wireless sensor nodes that will populate the Industrial Internet of Things (IIoT). In many applications, the sensor nodes will need to be installed in locations that are difficult to reach let alone...
Continue Reading![How to Interface Flux Sensor How to Interface Flux Sensor](https://www.electronics-lab.com/wp-content/uploads/2016/07/FTPT8KKIQ6UO9TH.MEDIUM.jpg)
How to Interface Flux Sensor
This tutorial is going to teach you the basics on using Flux Sensor: It is a flex sensor which is 2.2 inches in length. This sensor works by bending the sensor itself. As the sensor is being flexed or bent, the resistance across the sensor increases. The greater the angle of bending,...
Continue Reading![An Introduction to LiPo Batteries An Introduction to LiPo Batteries](https://www.electronics-lab.com/wp-content/uploads/2016/07/LiPo-Battery-1024x683-1024x683.jpg)
An Introduction to LiPo Batteries
Average Man Vs Raspberry Pi has a handy article on LiPo batteries. LiPo batteries – to fear or not to fear? Up until very recently, I was petrified. Whilst most other competitors at Pi Wars 2015 were happily using this angry and volatile battery technology, Average Man over...
Continue Reading![Fluke 15B+ Digital Multimeter Upgraded with ESP8266 Fluke 15B+ Digital Multimeter Upgraded with ESP8266](https://www.electronics-lab.com/wp-content/uploads/2016/07/IMG_0122-scaled-1024x683.jpg)
Fluke 15B+ Digital Multimeter Upgraded with ESP8266
SpritesMods has a 5-part write-up that shows how to add wireless connectivity to a Fluke 15B+ digital multimeter All in all, I feel like I have succesfully diversified my multimeter assortment. I have a Fluke 17B I can use for daily work so I can enjoy quick continuity testing and...
Continue Reading