![Make the PCB from your design using Altium CircuitStudio Make the PCB from your design using Altium CircuitStudio](https://www.electronics-lab.com/wp-content/uploads/2016/07/pastedImage_17.png)
Make the PCB from your design using Altium CircuitStudio
AshokRao guide us through the process of creating a PCB out of your Schematic, using Altium - CircuitStudio OK, further to Part 1 of this blog where we created a schematic, now it’s time to move to the PCB. If you still don't have your license, get a trail from...
Continue Reading![Smart LED Flashlight Smart LED Flashlight](https://www.electronics-lab.com/wp-content/uploads/2016/07/FO5DTB1IP76TH2Q.MEDIUM.jpg)
Smart LED Flashlight
Vitaliy_M @ instructables.com has build a nice little LED flashlight. The flashlight turns on automatic for 60 seconds when it senses that the room is dark enough. To turn on manual light for additional 60 seconds you need to push the RST button. Smart LED Flashlight -...
Continue Reading![Wemos D1 mini: A first look at this ESP8266 based board Wemos D1 mini: A first look at this ESP8266 based board](https://www.electronics-lab.com/wp-content/uploads/2016/07/wemos-d1-mini-a-first-look-at-th.jpg)
Wemos D1 mini: A first look at this ESP8266 based board
educ8s.tv has a new video discussing about the Wemos D1 mini board. In this video we are going to take a first look at the Wemos D1 mini board. The new impressive ESP8266 based board. It is very small in size, very inexpensive but very powerful! If you have watched some of my...
Continue Reading![IN-4 Nixie Clock using ATmega168 IN-4 Nixie Clock using ATmega168](https://www.electronics-lab.com/wp-content/uploads/2016/07/FBRONSFHQ70VV3B.MEDIUM.jpg)
IN-4 Nixie Clock using ATmega168
andrea biffi @ instructables.com has a detailed tutorial on how to build your own Nixie clock using IN-4 tubes and Atmel ATMega168 microcontroller. Nixies are neon valve tubes, where ten cathodes have shape of digits and are lighted up by plasma when high voltage flows through them....
Continue Reading![Arduino LED Scroll Bar using easyEDA Arduino LED Scroll Bar using easyEDA](https://www.electronics-lab.com/wp-content/uploads/2016/07/12.png)
Arduino LED Scroll Bar using easyEDA
Today I want to make a LED Scroll Bar as is shown in the picture above. Ten LED strips can flash in different effect by using a control board. Components: LED strip, Arduino Nano, Dupont line and a control board. Arduino LED Scroll Bar using easyEDA -...
Continue Reading![SmartWatering – Arduino plant watering SmartWatering – Arduino plant watering](https://www.electronics-lab.com/wp-content/uploads/2016/07/Prototype-1024x807.jpg)
SmartWatering – Arduino plant watering
Arduino based project in charge of taking care of your green plant. Particle Core based project in charge of taking care of my green plants. The water pump will not work with a voltage under 5V. In order to power it, I soldered a wire straight on the VUSB pin of the USB header....
Continue Reading![Easy Planter – A Simple Way Of Monitoring Plants Easy Planter – A Simple Way Of Monitoring Plants](https://www.electronics-lab.com/wp-content/uploads/2016/07/easyplanter.png)
Easy Planter – A Simple Way Of Monitoring Plants
Easy Planter is a plant monitoring device able to sense temperature, humidity, pressure, moisture, light etc. A small bluetooth low energy plant sensor that easily fits into a plant pot. It can monitor temperature, humidity, pressure, moisture, light, and has I2C extension pins so...
Continue Reading![One Channel Infra Red Remote Controller One Channel Infra Red Remote Controller](https://www.electronics-lab.com/wp-content/uploads/2016/07/H015-500x500-e1555490996562.jpg)
One Channel Infra Red Remote Controller
One Channel Infra-Red Remote and receiver with onboard Relay provides normally open and normally closed output. The project based on PIC12F683 Microcontroller from Microchip , TSOP1738 used as Infra-Red receiver. Micro-controller decodes the RC5 serial data coming from TSOP1738 and...
Continue Reading