Category: Motor
![Control Nema Stepper Motor With Arduino Control Nema Stepper Motor With Arduino](https://www.electronics-lab.com/wp-content/uploads/2017/01/F7YO44DIVHQL9IJ.MEDIUM.jpg)
Control Nema Stepper Motor With Arduino
Robokits @ instructables.com have an article describing stepper motors and how to drive them using Arduino. They write: Lots of People want to build Them own small Cnc machine . they started with drives stepper motor but they stacked in controller Programming . In this instructable...
Continue Reading![Wembi – Closed Loop Motorupgrade for 3D Printer Wembi – Closed Loop Motorupgrade for 3D Printer](https://www.electronics-lab.com/wp-content/uploads/2017/01/ea80b22f39aac206ed590efd9c8e43bd_original.png)
Wembi – Closed Loop Motorupgrade for 3D Printer
TeamVenture-Bit tipped us with their kickstarter campaign. It's about a closed loop motor upgrade kit that will enable your 3D printer to print faster, silently and more consistently. Check it out. Boasting an advanced PID compensation system that detects issues while your 3D printer...
Continue Reading![STEP/DIR SIGNAL TO CW/CWW SIGNAL CONVERTER FOR CNC & MOTION CONTROL SYSTEMS STEP/DIR SIGNAL TO CW/CWW SIGNAL CONVERTER FOR CNC & MOTION CONTROL SYSTEMS](https://www.electronics-lab.com/wp-content/uploads/2016/12/STEP-DIR-SIGNAL-TO-CW-CWW-SIGNAL-CONVERTER-PIC.jpg)
STEP/DIR SIGNAL TO CW/CWW SIGNAL CONVERTER FOR CNC & MOTION CONTROL SYSTEMS
Simple Circuit converts Step/Dir. signal into to double drive CW/CWW Pulse, Mach3 and few Hobby CNC software’s provides Step/Direction pulse output to drive stepper motor drivers. Various AC servo works with double CW/CCW pulse. This circuit is solution to interface such AC...
Continue Reading![4.5A H-Bridge DC Motor Driver Module Using TB6549HQ 4.5A H-Bridge DC Motor Driver Module Using TB6549HQ](https://www.electronics-lab.com/wp-content/uploads/2016/12/H-Bridge-DC-Motor-Driver-Module-pic.jpg)
4.5A H-Bridge DC Motor Driver Module Using TB6549HQ
The H-Bridge Motor Driver Module Based on TB6549HQ IC from Toshiba, is a full-bridge driver IC for DC motors that uses an LDMOS structure for output transistors. High-efficiency drive is possible through the use of a MOS process with low ON-resistance and a PWM drive system. Four...
Continue Reading![2X L298 Dual DC Motor Driver Board for Robots 2X L298 Dual DC Motor Driver Board for Robots](https://www.electronics-lab.com/wp-content/uploads/2016/12/L298-Dual-DC-Motor-Driver-Board-IMG2.jpg)
2X L298 Dual DC Motor Driver Board for Robots
2x L298 H-Bridge Dual Motor driver project can control two DC motors connected to it. The circuit is designed around popular dual H-Bridge L298 from ST. Motor supply 7V To 46V DC, Load 2Amp Each Channel. Features Motor supply V2: 7 to 46 VDC Logic Supply V1 : 5V DC...
Continue Reading![DC Motor & Direction Controller with Brake using MC33035 DC Motor & Direction Controller with Brake using MC33035](https://www.electronics-lab.com/wp-content/uploads/2016/12/DC-MOTOR-SPEED-DIRECTION-CONTROLLER-M137.jpg)
DC Motor & Direction Controller with Brake using MC33035
This is a 3AMP DC Motor speed and direction controller using MC33035 IC from on semiconductor, though the MC33035 was designed to control brushless DC motor , it may also be used to control DC brush type motors. MC33035 driving a Mosfets based H-Bridge affording minimal parts count to...
Continue Reading![2.5A Bipolar Stepper Motor Driver using A3979 2.5A Bipolar Stepper Motor Driver using A3979](https://www.electronics-lab.com/wp-content/uploads/2016/11/2.5A-BIPOLAR-STEPPER-MOTOR-DRIVER-M075A-500x500.jpg)
2.5A Bipolar Stepper Motor Driver using A3979
The tiny board designed using A3979 IC from ALLEGRO which is complete micro stepping driver with built in translator. The translator is the key to the easy implementation of the A3979. It allows the simple input of one pulse on the STEP pin to drive the motor one micro step, which can...
Continue Reading![Program a mBot With Scratch And Arduino Program a mBot With Scratch And Arduino](https://www.electronics-lab.com/wp-content/uploads/2016/11/program-a-mbot-with-scratch-and-1024x576.jpg)
Program a mBot With Scratch And Arduino
Makeblock was founded in 2012 in Shenzhen as the world's first open-source robot and programing platform. With more than 400 mechanical components, electronic modules, and software tools, the company is determined to bring meaningful STEM education opportunities and the maker mindset to...
Continue Reading