Search Results for : PCB
![Multiband IoT Antenna supports LTE, GPS, Bluetooth and WiFi Multiband IoT Antenna supports LTE, GPS, Bluetooth and WiFi](https://www.electronics-lab.com/wp-content/uploads/2020/07/0830AT54A2200E-Johanson-Technology-Inc.-RF-IF-and-RFID-DigiKey.png)
![](https://www.electronics-lab.com/wp-content/themes/elab/images/advertising_article_events_news_newspaper_icon.png)
Multiband IoT Antenna supports LTE, GPS, Bluetooth and WiFi
Johanson Technology's single antenna matching solution covers all relative frequency bands Multiple frequency, protocol, and functionality solutions for IoT connectivity continue to push size and performance limits. To address this, Johanson Technology developed a multiband flexible...
Continue Reading![Meet the Life Data Link Monitor Designed to Combat COVID-19 Meet the Life Data Link Monitor Designed to Combat COVID-19](https://www.electronics-lab.com/wp-content/uploads/2020/07/Life-Monitor.jpeg)
![](https://www.electronics-lab.com/wp-content/themes/elab/images/advertising_article_events_news_newspaper_icon.png)
Meet the Life Data Link Monitor Designed to Combat COVID-19
Covid-19 has inspired hundreds of health-related electronics projects from ventilators whose shortage was the initial worry for health professionals across the world to "basic" vital monitoring which was discovered to be very useful along the line. One of many projects which had...
Continue Reading![Photodiode Amplifier for Visible Light Using OPA381 – Arduino Nano Shield Photodiode Amplifier for Visible Light Using OPA381 – Arduino Nano Shield](https://www.electronics-lab.com/wp-content/uploads/2020/07/sch-1.jpg)
Photodiode Amplifier for Visible Light Using OPA381 – Arduino Nano Shield
The project presented here is a photodiode amplifier for visible light. The output voltage of the circuit increases linearly with light intensity. Low-cost BPW34 photodiode is used as a light sensor and OPA381 op-amp as an amplifier. OPA381 is a transimpedance amplifier that converts...
Continue Reading![Extremely small power-saving 3D magnetic sensor opens up new design options Extremely small power-saving 3D magnetic sensor opens up new design options](https://www.electronics-lab.com/wp-content/uploads/2020/07/Infineon_TLI493D-W2BW-e1595237270680-1024x600.jpg)
![](https://www.electronics-lab.com/wp-content/themes/elab/images/advertising_article_events_news_newspaper_icon.png)
Extremely small power-saving 3D magnetic sensor opens up new design options
Infineon Technologies AG will expand its XENSIV™ 3D magnetic sensor family TLx493D. At its in-house digital trade show "Virtual Sensor Experience", the chipmaker will present a new device for industrial and consumer applications: the TLI493D-W2BW. It uses the latest 3D Hall...
Continue Reading![Meet the KitDuino: The Atmega32u4 based Development Board Meet the KitDuino: The Atmega32u4 based Development Board](https://www.electronics-lab.com/wp-content/uploads/2020/07/kitduino.jpg)
![](https://www.electronics-lab.com/wp-content/themes/elab/images/advertising_article_events_news_newspaper_icon.png)
Meet the KitDuino: The Atmega32u4 based Development Board
While some may think the era of the Arduino Clones is over, the reverse is the case as more designers are, on a daily basis, releasing a different open-source version of boards that addresses one shortcoming or the other in the Original Arduino board. Sometimes, these reasons behind the...
Continue Reading![Meet the IoT-Ready, Esp32-based Maia Development Board Meet the IoT-Ready, Esp32-based Maia Development Board](https://www.electronics-lab.com/wp-content/uploads/2020/07/ma-1.png)
![](https://www.electronics-lab.com/wp-content/themes/elab/images/advertising_article_events_news_newspaper_icon.png)
Meet the IoT-Ready, Esp32-based Maia Development Board
So far so good, only a few boards have been able to take advantage of the extra USB OTG interface offered by the ESP32-S2 processor released back in 2019, and one of them is the new Maia development board from Stetel Things. As a quick reminder, the ESP32-S2 was unveiled with quite...
Continue Reading![Vishay Intertechnology 30 V MOSFET Half-Bridge Power Stage Delivers 11 % Higher Output Current in PowerPAIR® 3x3F Vishay Intertechnology 30 V MOSFET Half-Bridge Power Stage Delivers 11 % Higher Output Current in PowerPAIR® 3x3F](https://www.electronics-lab.com/wp-content/uploads/2020/07/742-6043-8-e1594368263732.jpg)
![](https://www.electronics-lab.com/wp-content/themes/elab/images/advertising_article_events_news_newspaper_icon.png)
Vishay Intertechnology 30 V MOSFET Half-Bridge Power Stage Delivers 11 % Higher Output Current in PowerPAIR® 3x3F
Vishay Intertechnology, Inc. today introduced a new 30 V n-channel MOSFET half-bridge power stage that combines a high side TrenchFET® MOSFET and low side SkyFET® MOSFET with an integrated Schottky diode in one compact PowerPAIR® 3.3 mm by 3.3 mm package. For power conversion in...
Continue Reading![2.4 GHz Modules: Proteus-III and Thyone-I 2.4 GHz Modules: Proteus-III and Thyone-I](https://www.electronics-lab.com/wp-content/uploads/2020/07/o169575v209-Family_Thyone-I_-2611011021000--e1594367656591.jpg)
![](https://www.electronics-lab.com/wp-content/themes/elab/images/advertising_article_events_news_newspaper_icon.png)
2.4 GHz Modules: Proteus-III and Thyone-I
Würth Elektronik’s 2.4 GHz modules feature six configurable I/O pins and a small 8 mm x 12 mm size Würth Elektronik offers the Bluetooth® Low Energy 5.1 module Proteus-III and the proprietary version Thyone-I. The modules measure only 8 mm x 12 mm x 2 mm, feature an...
Continue Reading