Search Results for : PCB
![RMS Noise to DC Converter – RMS Noise Measurement RMS Noise to DC Converter – RMS Noise Measurement](https://www.electronics-lab.com/wp-content/uploads/2024/05/001-9-1024x532.jpg)
RMS Noise to DC Converter – RMS Noise Measurement
This mini-module helps users to measure the RMS noise of AC signal. Apply the AC noise signal to the input and the circuit outputs a DC voltage. Signal bandwidth is 1Khz to 100Khz and input sensitivity is 1 μVolt RMS. The LT6203 ultra-low noise, low power op-amp amplifies the...
Continue Reading![RMS To DC Converter RMS To DC Converter](https://www.electronics-lab.com/wp-content/uploads/2024/05/007-8-1024x623.jpg)
RMS To DC Converter
This is a Precision Micro-power true RMS-to-DC converter built using LTC1966 RMS to DC Converter chip and op-amp LTC1494. The RMS to DC that is Converted by LTC1966 and op-amp is used as a post filter to improve AC Response with Offset and Gain Correction. The circuit converts the AC...
Continue Reading![Lamp Flasher with Timer IC and MOSFET for Automotive Applications Lamp Flasher with Timer IC and MOSFET for Automotive Applications](https://www.electronics-lab.com/wp-content/uploads/2024/05/003-7-1024x487.jpg)
Lamp Flasher with Timer IC and MOSFET for Automotive Applications
This is a mini flasher board that can drive high-power LED or a lamp, mainly designed for automotive applications. The project consists BD9555FVM-C timer chip and MOSFET. The circuit is configured as a flasher, and can also be used as a PWM driver with an adjustable duty cycle and...
Continue Reading![One Channel RF Remote Relay Switch One Channel RF Remote Relay Switch](https://www.electronics-lab.com/wp-content/uploads/2024/05/002-5-1024x651.jpg)
One Channel RF Remote Relay Switch
The project described here is one Channel RF remote receiver Relay board. The project is built using LICAL-EDC-DS001 chip from LINX. The board consists of Encoder/Decoder chip, 433Mhz RF Receiver module, 10 x jumpers to set the address, a Relay to drive the output, U2 5V regulator,...
Continue Reading![High-Voltage (180V) – High-Current (30mA) Operational Amplifier Module High-Voltage (180V) – High-Current (30mA) Operational Amplifier Module](https://www.electronics-lab.com/wp-content/uploads/2024/05/009-5-1024x797.jpg)
High-Voltage (180V) – High-Current (30mA) Operational Amplifier Module
This project provides a platform to evaluate the OPA462 high-voltage, high-current operational amplifier. Multiple component footprints allow the most common circuit configurations. The board accommodates high-voltage and high-current operational amplifier OPA462 from Texas...
Continue Reading![High Voltage 3-Phase Full-Wave PWM Brushless Motor Driver High Voltage 3-Phase Full-Wave PWM Brushless Motor Driver](https://www.electronics-lab.com/wp-content/uploads/2024/05/012-3-1024x862.jpg)
High Voltage 3-Phase Full-Wave PWM Brushless Motor Driver
The project presented here is a three-phase sinewave PWM driver for high-voltage brushless motors. The board is built using TB67B000AHG chip, which is a high-voltage IC capable of handling 600V. The TB67B000AHG has a 2-in-1 (MCP) structure of controller (sine-wave PWM / wide-angle...
Continue Reading![Waveshare ESP32-S3-Matrix Dev Board Features A 8×8 RGB LED Matrix with Attitude Sensors Waveshare ESP32-S3-Matrix Dev Board Features A 8×8 RGB LED Matrix with Attitude Sensors](https://www.electronics-lab.com/wp-content/uploads/2024/05/ESP32-S3-Matrix-Dev-Board-Specifications.jpg)
![](https://www.electronics-lab.com/wp-content/themes/elab/images/advertising_article_events_news_newspaper_icon.png)
Waveshare ESP32-S3-Matrix Dev Board Features A 8×8 RGB LED Matrix with Attitude Sensors
Waveshare ESP32-S3-Matrix Dev Board is an ESP32-S3-based development board that features an 8×8 addressable RGB LED Matrix(64 LEDs in total), 15 usable GPIO pins, and a 9-axis attitude sensor that can be used for robotics and motion control applications. In addition to that it is...
Continue Reading![Over Current Alarm with 15 Segment Bar-Graph Display Over Current Alarm with 15 Segment Bar-Graph Display](https://www.electronics-lab.com/wp-content/uploads/2024/05/011-4-1024x799.jpg)
Over Current Alarm with 15 Segment Bar-Graph Display
This Bar-Graph Display provides a high visibility 15-Segment Bar-Graph display for current measurements. A buzzer provides audible sound when an over-current condition event occurs. The 15 segments are made with Red, Blue, Green, and yellow color LEDS. All LEDs are SMD size 1206. This...
Continue Reading