Search Results for : arduino uno
![Low Cost Room Thermometer Using 16×2 LCD and Atmega328 Low Cost Room Thermometer Using 16×2 LCD and Atmega328](https://www.electronics-lab.com/wp-content/uploads/2020/12/Schematic-1.jpg)
Low Cost Room Thermometer Using 16×2 LCD and Atmega328
This is an easy to build small size and low-cost room thermometer. The project consists of LM35 analog temperature sensor, 16x2 LCD, and an Atmega328 chip. This compact board is Arduino compatible and provided with an onboard connector for Boot-Loader burning and Arduino IDE...
Continue Reading![Tiny1284P is Based on ATmega1284P microcontroller and Uses USB Type-C for Power and Programming Tiny1284P is Based on ATmega1284P microcontroller and Uses USB Type-C for Power and Programming](https://www.electronics-lab.com/wp-content/uploads/2020/08/Screen-Shot-2020-08-07-at-7.26.29-AM-1024x287.jpg)
![](https://www.electronics-lab.com/wp-content/themes/elab/images/advertising_article_events_news_newspaper_icon.png)
Tiny1284P is Based on ATmega1284P microcontroller and Uses USB Type-C for Power and Programming
Hayri Uygur is set to launch his new product: a tiny, breadboard-friendly and open-source Arduino-compatible development board, aptly-named Tiny1284P. The Tiny1284P development board is built around the high-performance low cost ATmega1284P-AU 8-bit microcontroller that combines 16KB of...
Continue Reading![microUPDI – Pro-Micro Based UPDI Programmer microUPDI – Pro-Micro Based UPDI Programmer](https://www.electronics-lab.com/wp-content/uploads/2020/07/updi1.jpg)
![](https://www.electronics-lab.com/wp-content/themes/elab/images/advertising_article_events_news_newspaper_icon.png)
microUPDI – Pro-Micro Based UPDI Programmer
Thanks to the increased popularity of the recent ATtiny series of microcontrollers, there has been an increase in the number of open-source UPDI programmers out there. We have covered quite a number of them including the brilliant UPDI programmer compatible with Arduino IDE but we...
Continue Reading![Gravity: I2C Oxygen Sensor is on sale for $53.90 Gravity: I2C Oxygen Sensor is on sale for $53.90](https://www.electronics-lab.com/wp-content/uploads/2020/06/SEN0322.jpg)
![](https://www.electronics-lab.com/wp-content/themes/elab/images/advertising_article_events_news_newspaper_icon.png)
Gravity: I2C Oxygen Sensor is on sale for $53.90
The Gravity: I2C Oxygen Sensor is based on electrochemical principles and it can measure the ambient O2 concentration accurately and conveniently. With high anti-interference ability, high stablility and high sensitivity, this arduino-compatible oxygen sensor can be widely applied to...
Continue Reading![A new ATMega328p board with onboard OLED Display A new ATMega328p board with onboard OLED Display](https://www.electronics-lab.com/wp-content/uploads/2020/06/Atmega-328p-board-back-1024x682.jpeg)
![](https://www.electronics-lab.com/wp-content/themes/elab/images/advertising_article_events_news_newspaper_icon.png)
A new ATMega328p board with onboard OLED Display
Made popular by the Arduino based on it, the Atmega328p has become one of the most popular microcontrollers around, thanks to the ease with which it can be programmed using the Arduino IDE. Either as a direct clone of Arduino boards like Uno and Nano or as a new board with an entirely...
Continue Reading![Top 10 Popular Microcontrollers Among Makers Top 10 Popular Microcontrollers Among Makers](https://www.electronics-lab.com/wp-content/uploads/2020/06/F7589339-01.jpg)
![](https://www.electronics-lab.com/wp-content/themes/elab/images/advertising_article_events_news_newspaper_icon.png)
Top 10 Popular Microcontrollers Among Makers
At the heart of any embedded electronics device, either on a DIY or professional product level is a microcontroller. They run the codes/firmware that helps developers obtain inputs from sensors and tie it to actions executed through actuators. While they are usually developed as...
Continue Reading![Infineon Technologies S2GO MEMSMIC IM69D Shield2Go Board Infineon Technologies S2GO MEMSMIC IM69D Shield2Go Board](https://www.electronics-lab.com/wp-content/uploads/2020/06/175383194.png)
![](https://www.electronics-lab.com/wp-content/themes/elab/images/advertising_article_events_news_newspaper_icon.png)
Infineon Technologies S2GO MEMSMIC IM69D Shield2Go Board
Infineon Technologies S2GO MEMSMIC IM69D Shield2Go Board is a "plug and play" prototyping board based on the Shield2Go Evaluation Environment, and featuring two IM69D130 High-performance Digital MEMS Microphones. Infineon Technology IM69D130 is a High-performance Digital MEMS...
Continue Reading![USBASP Firmware update guide USBASP Firmware update guide](https://www.electronics-lab.com/wp-content/uploads/2020/06/usbasp-firmware-update-connections-1024x426.jpg)
USBASP Firmware update guide
The USBASP programmer is an important tool/accessory for embedded systems engineers/ firmware developers. It is a USB ICSP (In-Circuit Serial Programmer) that allows developers to easily upload firmware/bootloaders on AVR microcontrollers. Unlike what you find to serial programmers like...
Continue Reading