Search Results for : PCB
![350W Power Factor Boost Converter for Inverter-Fed BLDC and PMSM Motors 350W Power Factor Boost Converter for Inverter-Fed BLDC and PMSM Motors](https://www.electronics-lab.com/wp-content/uploads/2023/08/005-4-1024x793.jpg)
350W Power Factor Boost Converter for Inverter-Fed BLDC and PMSM Motors
This 350W power factor boost converter is designed for inverter-fed BLDC/PMSM motor appliances, A/C units, Refrigerators, and industrial power supplies. The circuit is a continuous-conduction-mode boost converter implemented using a UCC28180 PFC controller module which provides all...
Continue Reading![Two Channel High Side Driver with Analog Sense for Automotive Applications Two Channel High Side Driver with Analog Sense for Automotive Applications](https://www.electronics-lab.com/wp-content/uploads/2023/08/007-4-1024x739.jpg)
Two Channel High Side Driver with Analog Sense for Automotive Applications
The project presented here is suitable for all types of resistive, inductive, and capacitive loads, and can also be used to drive LEDs. The board is built using 2 x VN5025AJ chips which are monolithic devices made using STMicroelectronics VIPower technology. It is intended for driving...
Continue Reading![Breakout Board for UCC28019 and UCC28128 PFC Controller Breakout Board for UCC28019 and UCC28128 PFC Controller](https://www.electronics-lab.com/wp-content/uploads/2023/08/002-4-1024x484.jpg)
Breakout Board for UCC28019 and UCC28128 PFC Controller
This is a breakout board for UCC28019 and UCC28128 PFC controllers. This module enables users to build a high-power PFC (Power Factor Correction) controller. Active PFC uses the boost topology operating in Continuous Conduction Mode (CCM). The controller is suitable for systems in the...
Continue Reading![High Power Bipolar Stepper Motor Driver with SPI Interface High Power Bipolar Stepper Motor Driver with SPI Interface](https://www.electronics-lab.com/wp-content/uploads/2023/08/002-3-1024x835.jpg)
High Power Bipolar Stepper Motor Driver with SPI Interface
This is a compact high-power stepper motor driver built for bipolar stepper motors. The driver can be controlled using a serial communication interface (SPI). It combines a flexible ramp generator for automatic target positioning with the industry’s most advanced stepper motor...
Continue Reading![DC Motor Position Control Using Potentiometer – Arduino Compatible DC Motor Position Control Using Potentiometer – Arduino Compatible](https://www.electronics-lab.com/wp-content/uploads/2023/08/002-2-1024x852.jpg)
DC Motor Position Control Using Potentiometer – Arduino Compatible
The project presented here is an Arduino-compatible motor control board. The board consists of an ATMEGA328 microcontroller, LMD18201 H-Bridge, and 2 x potentiometers. This closed-loop servo system provides position control using a feedback potentiometer mounted on the output shaft of...
Continue Reading![Self-Oscillating Full-Bridge Using IRS2453 Self-Oscillating Full-Bridge Using IRS2453](https://www.electronics-lab.com/wp-content/uploads/2023/08/003-2-1024x826.jpg)
Self-Oscillating Full-Bridge Using IRS2453
This is a Self-oscillating full-bridge project built using the IRS2453 chip. This chip incorporates a high-voltage full-bridge gate driver with a front-end oscillator similar to the industry standard CMOS 555 timer. HVIC and latch-immune CMOS technologies enable ruggedized monolithic...
Continue Reading![Function Generator Using AD9833 DDS – Arduino Compatible Function Generator Using AD9833 DDS – Arduino Compatible](https://www.electronics-lab.com/wp-content/uploads/2023/08/004-1-1024x728.jpg)
Function Generator Using AD9833 DDS – Arduino Compatible
This is an Arduino-compatible hardware designed for building a low-cost function generator. The project consists of all the required spices to build your own function generator. It includes multiple options such as a potentiometer, rotary encoder, tactile switches, op-amp, and 16x2...
Continue Reading![DC Electronic Load – 1A DC Electronic Load – 1A](https://www.electronics-lab.com/wp-content/uploads/2023/08/001-1024x614.jpg)
DC Electronic Load – 1A
This is a very precise Electronic Load project built using the ultra-Precision, Low-Noise OPAMP MAX44251 from Analog Devices. The project can sink current from a power source. It can be used as test gear for power supplies, chargers, solar panels, batteries, and DC-DC converters. The...
Continue Reading