Search Results for : Arduino
![AmpRipper 4000 is a New Battery supply Board for Raspberry Pi & Arduino AmpRipper 4000 is a New Battery supply Board for Raspberry Pi & Arduino](https://www.electronics-lab.com/wp-content/uploads/2023/02/01-1024x807.jpg)
![](https://www.electronics-lab.com/wp-content/themes/elab/images/advertising_article_events_news_newspaper_icon.png)
AmpRipper 4000 is a New Battery supply Board for Raspberry Pi & Arduino
Kickstart Design is preparing to launch a campaign on Kickstarter for the AmpRipper 4000, their next-generation battery supply board for Raspberry Pi, Arduino, and other electronic projects, which is set to launch soon - boasting a significant upgrade from the AmpRipper 3000 design. In...
Continue Reading![Expansion Shield – Breakout Board for Arduino Nano Expansion Shield – Breakout Board for Arduino Nano](https://www.electronics-lab.com/wp-content/uploads/2023/02/2-55-1024x768.jpg)
![](https://www.electronics-lab.com/wp-content/themes/elab/images/basket_buy_cart_store basket_trolley_icon.png)
Expansion Shield – Breakout Board for Arduino Nano
If you need to interface many devices and sensors to Arduino Nano, then, this project is for you. This is a Nano expansion I/O shield (breakout board) for the Arduino Nano. The board facilitates the easy connection between Arduino Nano and other devices. Each Arduino (I/O) Pin including...
Continue Reading![An affordable SDI signal generator using Arduino MKR Vidor 4000 An affordable SDI signal generator using Arduino MKR Vidor 4000](https://www.electronics-lab.com/wp-content/uploads/2023/02/Untitled.jpg)
![](https://www.electronics-lab.com/wp-content/themes/elab/images/advertising_article_events_news_newspaper_icon.png)
An affordable SDI signal generator using Arduino MKR Vidor 4000
Transmission of video from one location to another in the professional video world is typically done via SDI (Serial Digital Interface). This FPGA-powered device, intended as a test tool for SDI circuits, pushes signals at 1.485 Gbps. Based on an Arduino MKR Vidor 4000, Chris Brown of...
Continue Reading![Translating “Dah” and “Dit” Speech Into Morse Code with an CWVox using Arduino Translating “Dah” and “Dit” Speech Into Morse Code with an CWVox using Arduino](https://www.electronics-lab.com/wp-content/uploads/2023/02/arduino-1024x570.jpg)
![](https://www.electronics-lab.com/wp-content/themes/elab/images/advertising_article_events_news_newspaper_icon.png)
Translating “Dah” and “Dit” Speech Into Morse Code with an CWVox using Arduino
image: CWvox Prototype connected to the radio (Source: Kevin Loughin) These days, it seems like every speech-detection-related project is based on some kind of advanced algorithm, such as machine learning, pattern matching, or spectrum analysis. But Kevin Loughin (AKA KB9RLW), an...
Continue Reading![2.7A PWM Valve/Solenoid Driver Arduino Nano Shield 2.7A PWM Valve/Solenoid Driver Arduino Nano Shield](https://www.electronics-lab.com/wp-content/uploads/2023/02/2-38-1024x768.jpg)
![](https://www.electronics-lab.com/wp-content/themes/elab/images/basket_buy_cart_store basket_trolley_icon.png)
2.7A PWM Valve/Solenoid Driver Arduino Nano Shield
This Arduino shield helps to drive various loads like a solenoid, valve, motor, inductive actuator, heater, and bulb. A wide supply range 8V-60V and a load current of 2.7A allows it to be used with a variety of actuators. The board can be used as a stand-alone driver or it can be...
Continue Reading![Arduino 2-Digit 0.5″ Common Cathode 7 Segment Display Module Arduino 2-Digit 0.5″ Common Cathode 7 Segment Display Module](https://www.electronics-lab.com/wp-content/uploads/2023/02/2-24-1024x768.jpg)
![](https://www.electronics-lab.com/wp-content/themes/elab/images/basket_buy_cart_store basket_trolley_icon.png)
Arduino 2-Digit 0.5″ Common Cathode 7 Segment Display Module
This is an Arduino-compatible board for creating 2 Digit Display projects. The circuit operates with 5V DC, Connector CN1 is provided for bootloader programming and Arduino firmware upload. A new Atmega328 chip requires a bootloader and Arduino firmware programming, Connector CN1 helps...
Continue Reading![Two Channel Smart Low-Side Power Switch for Inductive, Resistive and Capacitive Loads – Arduino Shield Two Channel Smart Low-Side Power Switch for Inductive, Resistive and Capacitive Loads – Arduino Shield](https://www.electronics-lab.com/wp-content/uploads/2023/02/2-20-1024x768.jpg)
![](https://www.electronics-lab.com/wp-content/themes/elab/images/basket_buy_cart_store basket_trolley_icon.png)
Two Channel Smart Low-Side Power Switch for Inductive, Resistive and Capacitive Loads – Arduino Shield
The project presented here enables users to switch all kinds of resistive, inductive and capacitive loads, limited by clamping energy (EAS) and maximum current requirement. The user may interface 2 x inductive, resistive, and capacitive loads such as solenoid, dc motor, high current...
Continue Reading![Learn how! Robotic ultraArm P340 by Arduino sketches, engraves, and grabs Learn how! Robotic ultraArm P340 by Arduino sketches, engraves, and grabs](https://www.electronics-lab.com/wp-content/uploads/2023/01/全家福-scaled-1024x575.jpg)
![](https://www.electronics-lab.com/wp-content/themes/elab/images/advertising_article_events_news_newspaper_icon.png)
Learn how! Robotic ultraArm P340 by Arduino sketches, engraves, and grabs
The Elephant Robotics ultraArm P340 is a robot arm that has a working radius of 340 mm and is controlled by an Arduino-compatible ATMega2560 control board. The arm of this robot may be outfitted with a variety of accessories that can be used for painting, laser engraving, or grabbing...
Continue Reading