Archives: Projects
![Contactless Potentiometer – 12bit Rotary Position Sensor with Analog or PWM Output Contactless Potentiometer – 12bit Rotary Position Sensor with Analog or PWM Output](https://www.electronics-lab.com/wp-content/uploads/2023/07/011-1024x541.jpg)
Contactless Potentiometer – 12bit Rotary Position Sensor with Analog or PWM Output
This is an easy-to-program magnetic rotary position sensor with high-resolution 12-bit analog or PWM output. This contactless system measures the absolute angle of a diametric magnetized on-axis magnet. The project is designed for contactless potentiometer applications and its robust...
Continue Reading![Installation of Casa OS on Raspberry Pi Installation of Casa OS on Raspberry Pi](https://www.electronics-lab.com/wp-content/uploads/2023/05/1.png)
Installation of Casa OS on Raspberry Pi
In this tutorial, I will show you how to build a beautiful home server with Raspberry Pi and CasaOS. Things Needed All you need is a Raspberry Pi 4B board, That's all. Introduction to Casa OS CasaOS is a simple, easy-to-use, elegant open-source home cloud system that allows...
Continue Reading![Brushed DC Motor Speed Controller Using Radio Control (RC) Remote Brushed DC Motor Speed Controller Using Radio Control (RC) Remote](https://www.electronics-lab.com/wp-content/uploads/2023/05/003-9-1024x896.jpg)
Brushed DC Motor Speed Controller Using Radio Control (RC) Remote
This is a Brushed DC motor controller designed to control one brushed DC motor up to 5A. It can control the speed of the DC motor using a Radio Control (RC) System. This Arduino compatible hardware converts RC PWM signal into 0 to 100% duty cycle PWM which further drives high current...
Continue Reading![RC Radio Controlled Switch with Relay RC Radio Controlled Switch with Relay](https://www.electronics-lab.com/wp-content/uploads/2023/05/002-11-1024x603.jpg)
RC Radio Controlled Switch with Relay
This RC Relay project enables control of large current devices using a Radio Control (RC) System. This RC switch converts hobby radio control (RC) pulses to control the on/off state of the Relay. On board LED indicates the output. The board is Arduino compatible and the example code...
Continue Reading![Video Driver with Built-in 6 Channel Input Selection Switch Video Driver with Built-in 6 Channel Input Selection Switch](https://www.electronics-lab.com/wp-content/uploads/2023/05/002-10-1024x616.jpg)
Video Driver with Built-in 6 Channel Input Selection Switch
The project presented here is a video driver with 6 channel input selection using onboard jumpers or a microcontroller interface. The circuit features a wide dynamic range and frequency response. The IC can be used with low voltage starting at VCC=2.8V and the project supports a broad...
Continue Reading![Linear Current Source LED Driver with Dimmer Input Linear Current Source LED Driver with Dimmer Input](https://www.electronics-lab.com/wp-content/uploads/2023/05/003-7-1024x538.jpg)
Linear Current Source LED Driver with Dimmer Input
The compact module shown here is a linear current source for LED driver and it's ideal for automotive LED lighting applications. The project is built using a TLD1211 chip from Infineon. The board provides supply to LEDs under the severe condition of automotive applications resulting...
Continue Reading![8 Channel RF Remote Receiver with Holtek and Serial Protocol 8 Channel RF Remote Receiver with Holtek and Serial Protocol](https://www.electronics-lab.com/wp-content/uploads/2023/05/004-7-1024x673.jpg)
8 Channel RF Remote Receiver with Holtek and Serial Protocol
The project described here is 8 Channel RF Remote Receiver (Decoder). This 8-channel decoder is built using LICAL-EDC-DS001 chip from LINX. The board consists of the encoder/Decoder chip, 433Mhz RF Receiver module, and 10 x jumpers to set the address. Also, there is a header connector...
Continue Reading![8 Channel RF Remote Transmitter with Holtek and Serial Protocol 8 Channel RF Remote Transmitter with Holtek and Serial Protocol](https://www.electronics-lab.com/wp-content/uploads/2023/05/006-7-1024x582.jpg)
8 Channel RF Remote Transmitter with Holtek and Serial Protocol
The project described here is an 8 Channel RF remote transmitter This transmitter is built using LICAL-EDC-DS001 chip from LINX. The project consists of the Encoder/Decoder chip, a 433Mhz RF module as a wireless link, 8 x tactile switches for operations, 10 x jumpers to set the...
Continue Reading