Archives: Projects
![LED Dimmer for Super High Brightness LEDs LED Dimmer for Super High Brightness LEDs](https://www.electronics-lab.com/wp-content/uploads/2022/07/005-3-1024x677.jpg)
LED Dimmer for Super High Brightness LEDs
This is a high-efficiency and reliability DC/DC converter with a dimming feature for super high brightness LEDs. The project is built using L6902D chip. L6902 is a complete and simple step-down switching regulator with adjustable current limit. The current control loop with external...
Continue Reading![Linear Actuator Controller with Limit Switch to prevent Overextension and Retraction Linear Actuator Controller with Limit Switch to prevent Overextension and Retraction](https://www.electronics-lab.com/wp-content/uploads/2022/07/003-1024x666.jpg)
Linear Actuator Controller with Limit Switch to prevent Overextension and Retraction
The project described here is a very useful device for use with linear actuators. This controller prevents the actuator from reaching the physical movement limits of the actuator, thus it prevents burnout of motor and physical/mechanical damage to the actuator itself to the...
Continue Reading![Under Voltage and Over Voltage Monitor for 5V Under Voltage and Over Voltage Monitor for 5V](https://www.electronics-lab.com/wp-content/uploads/2022/07/005-1024x790.jpg)
Under Voltage and Over Voltage Monitor for 5V
This project is built using MC33161 IC, which is a universal voltage monitor intended to be used in a wide variety of voltage sensing applications. The project offers an economical solution for positive and negative voltage detection. The circuit consists of two comparator channels...
Continue Reading![Dual MOSFET Driver – Two Channel DC SSR Using MOSFETS & Gate Driver Dual MOSFET Driver – Two Channel DC SSR Using MOSFETS & Gate Driver](https://www.electronics-lab.com/wp-content/uploads/2022/06/005-2-1024x603.jpg)
Dual MOSFET Driver – Two Channel DC SSR Using MOSFETS & Gate Driver
The project presented here is a dual-channel MOSFET DC relay. The project is capable of driving a 5A load on each channel with an input supply of 48V DC. The LTC7067 chip drives the two high-side N-Channel MOSFETS with supply voltages up to 48V DC. Its powerful 0.8Ω pull-down and...
Continue Reading![Over Speed Sensor – Over Speed Alarm using Magnetic Pickup Sensor Over Speed Sensor – Over Speed Alarm using Magnetic Pickup Sensor](https://www.electronics-lab.com/wp-content/uploads/2022/06/001A-1-1024x649.jpg)
Over Speed Sensor – Over Speed Alarm using Magnetic Pickup Sensor
This is an over-speed sensor module, that provides an audible warning and signals output when the speed of a machine is above a set point. The module can be used in applications such as Engines, Machines, Sports machines, and Fitness Equipment. The speed of the machine or engine can...
Continue Reading![Low-Cost LED Dimmer using LM3578 Low-Cost LED Dimmer using LM3578](https://www.electronics-lab.com/wp-content/uploads/2022/06/006-2-1024x495.jpg)
Low-Cost LED Dimmer using LM3578
This Low-cost LED dimer project includes two main parts, an LM3578 chip, and a MOSFET. The LM3578 generates a PWM signal, and Q1 MOSFET helps to drive a high current LED. The project also includes current limit feature. Over current trigger point is set to 1.1A. LED intensity can be...
Continue Reading![2.5W Stereo Audio Amplifier using LM4752 2.5W Stereo Audio Amplifier using LM4752](https://www.electronics-lab.com/wp-content/uploads/2022/06/002-1-1024x572.jpg)
2.5W Stereo Audio Amplifier using LM4752
The Stereo Audio Amplifier project shown here is capable of delivering 2.5W per channel of continuous average output power to 4Ω loads using a single 12V supply at 10% THD+N. The project is built using the LM4752 chip. This chip is specifically designed for single supply operations...
Continue Reading![Cooling Fan Controller Using Temperature Sensor LM35 Cooling Fan Controller Using Temperature Sensor LM35](https://www.electronics-lab.com/wp-content/uploads/2022/06/004-1024x634.jpg)
Cooling Fan Controller Using Temperature Sensor LM35
The project presented here is a low-cost solution for heat management of the heatsink and various equipment that requires automatic control of a cooling Fan. The project is built using a very cheap LM358 OPAMP. LM358 is used as a comparator, and a trimmer PR1 is provided to set the...
Continue Reading