Archives: Projects
![High Voltage DC Power Supply for Intelligent Power Modules High Voltage DC Power Supply for Intelligent Power Modules](https://www.electronics-lab.com/wp-content/uploads/2021/07/001-2-1024x877.jpg)
High Voltage DC Power Supply for Intelligent Power Modules
Although this power supply design is specific to the Intelligent Power Modules (IPM), the concepts and circuit design may be used for any power supply that requires high voltage output up to 400V DC and 6 A. It is an unregulated power supply, DC output is dependent on AC input. The...
Continue Reading![Joystick Controlled 2 x RC Servo motors – Arduino Compatible Joystick Controlled 2 x RC Servo motors – Arduino Compatible](https://www.electronics-lab.com/wp-content/uploads/2021/07/004-3-1024x602.png)
Joystick Controlled 2 x RC Servo motors – Arduino Compatible
This project enables easy control of 2 RC servo motors using a thumb joystick. This is an Arduino compatible project and it consists of a thumb joystick, ATMEGA328 microcontroller, filter capacitor on dc supply, and other components. The thumb joystick has 2 axes, X and Y. The...
Continue Reading![Humidity Meter Using OLED Display – Arduino Compatible Humidity Meter Using OLED Display – Arduino Compatible](https://www.electronics-lab.com/wp-content/uploads/2021/07/SCH-2-1024x692.jpg)
Humidity Meter Using OLED Display – Arduino Compatible
This is an easy to build, very compact, and low profile Arduino compatible platform to build a humidity meter/Gauge using a 0.96Inch OLED display. The project consists of Atmega328 microcontroller, 0.96Inch OLED display, 3.3V regulator, and HIH5030 analog humidity sensor from...
Continue Reading![Microphone Preamplifier – Sound Sensor Microphone Preamplifier – Sound Sensor](https://www.electronics-lab.com/wp-content/uploads/2021/07/002-1024x685.jpg)
Microphone Preamplifier – Sound Sensor
This is an easy to construct dual-stage microphone pre-amplifier. The project can be used as a sound sensor or microphone pre-amplifier. The 1st op-amp pre-amplify the very low-level signal coming from the condenser microphone and 2nd op-amp provides more boost to the audio signal....
Continue Reading![Stereo Balanced to Unbalanced Audio Converter Stereo Balanced to Unbalanced Audio Converter](https://www.electronics-lab.com/wp-content/uploads/2021/07/003-1024x961.jpg)
Stereo Balanced to Unbalanced Audio Converter
The primary role of this project is to convert a differential input audio signal into a single-ended output signal while rejecting noise that is common to both inputs (common-mode noise). The circuit presented here is a differential amplifier intended to receive balanced line...
Continue Reading![Voltage-Controlled Pulse Width Modulator (PWM) – PWM Signal Generator Voltage-Controlled Pulse Width Modulator (PWM) – PWM Signal Generator](https://www.electronics-lab.com/wp-content/uploads/2021/06/001-3-1024x531.jpg)
Voltage-Controlled Pulse Width Modulator (PWM) – PWM Signal Generator
This is an easy-to-use voltage to PWM converter. The project occupies very little space. The circuit is built using the versatile silicon timing device LT6992-1 chip. Pulse Width Modulation (PWM) Controlled by Simple 0V to 1V Analog Input, multiturn trimmer potentiometer provided to...
Continue Reading![Humidity Sensor – Humidity to Frequency Output Humidity Sensor – Humidity to Frequency Output](https://www.electronics-lab.com/wp-content/uploads/2021/06/010-1-1024x753.jpg)
Humidity Sensor – Humidity to Frequency Output
This sensor board provides frequency output as per relative humidity value. The project is based on a unique capacitive cell, this relative humidity sensor is designed for high volume, cost-sensitive applications such as office automation, automotive cabin air control, home...
Continue Reading![Active Rectifier Controller with Reverse Protection for Battery and Solar cell Active Rectifier Controller with Reverse Protection for Battery and Solar cell](https://www.electronics-lab.com/wp-content/uploads/2021/06/008a-1024x694.jpg)
Active Rectifier Controller with Reverse Protection for Battery and Solar cell
This demonstration circuit is an active rectifier with reverse protection for batteries in automotive applications. The project is designed for 5A load current. Two clamping diodes, D1 and D2, are used on the board to protect the IC from overvoltage spikes at the input. The input...
Continue Reading