Archives: Projects
![1.2V to 50V @ 3A – Adjustable Power Supply with 55Vdc Input 1.2V to 50V @ 3A – Adjustable Power Supply with 55Vdc Input](https://www.electronics-lab.com/wp-content/uploads/2021/03/003-4-1024x878.jpg)
1.2V to 50V @ 3A – Adjustable Power Supply with 55Vdc Input
The project presented here is a wide input voltage range non-isolated DC-DC Converter, that provides a regulated, adjustable output voltage. The operating input supply is 55V DC and output regulated from 1.2V to 50V DC. The project built using LM2576HVT-ADJ IC. Screw terminals...
Continue Reading![Two Channel Smart Low-Side Power Switch for Inductive, Resistive and Capacitive Loads – Arduino Shield Two Channel Smart Low-Side Power Switch for Inductive, Resistive and Capacitive Loads – Arduino Shield](https://www.electronics-lab.com/wp-content/uploads/2021/03/001-3-1024x783.jpg)
Two Channel Smart Low-Side Power Switch for Inductive, Resistive and Capacitive Loads – Arduino Shield
The project presented here enables users to switch all kinds of resistive, inductive and capacitive loads, limited by clamping energy (EAS) and maximum current requirement. The user may interface 2 x inductive, resistive, and capacitive loads such as solenoid, dc motor, high current...
Continue Reading![PIR Motion Sensor LED Ceiling Light – Arduino Compatible PIR Motion Sensor LED Ceiling Light – Arduino Compatible](https://www.electronics-lab.com/wp-content/uploads/2021/03/002-3-1024x864.jpg)
PIR Motion Sensor LED Ceiling Light – Arduino Compatible
This motion sensor LED ceiling light board has been designed using 4 white LEDs each of 1-3W, PIR sensor module, Atmega328 microcontroller, low ohm IRLR7843 MOSFET, and few other components. The PIR sensor detects the infra-red rays emitted by human motion within the detection area...
Continue Reading![16 High Power LEDs Knight Rider Light – Arduino Compatible 16 High Power LEDs Knight Rider Light – Arduino Compatible](https://www.electronics-lab.com/wp-content/uploads/2021/03/006-2-1024x697.jpg)
16 High Power LEDs Knight Rider Light – Arduino Compatible
This is a Knight Rider LED Light and it is one of the best Arduino projects for beginners. This board drives 16 high-power LEDs to turn them ON one by one sequentially. This is an open-source Arduino compatible project that contains 16 high current MOSFETs, Atmega328 microcontroller,...
Continue Reading![High Accuracy Adjustable Overvoltage and Overcurrent Protectors using MAX17561 High Accuracy Adjustable Overvoltage and Overcurrent Protectors using MAX17561](https://www.electronics-lab.com/wp-content/uploads/2021/03/004-1-1024x637.jpg)
High Accuracy Adjustable Overvoltage and Overcurrent Protectors using MAX17561
If you need safe power to run your project, then this circuit is a possible solution for you. This project provides protection to your system device against over-current, over-voltage, under-voltage, thermal overload, and reverse current flow control to the system device. Basically,...
Continue Reading![6-Channel Capacitive Touch Sensor Module 6-Channel Capacitive Touch Sensor Module](https://www.electronics-lab.com/wp-content/uploads/2021/03/001-1024x568.jpg)
6-Channel Capacitive Touch Sensor Module
The module described here is a 6-channel capacitive touch sensor. The project is based on CAP1206 IC which contains six (6) individual capacitive touch sensor inputs with programmable sensitivity for use in touch sensor applications. Each sensor input is calibrated to compensate for...
Continue Reading![LCDduino – Arduino Compatible 16×2 LCD module LCDduino – Arduino Compatible 16×2 LCD module](https://www.electronics-lab.com/wp-content/uploads/2021/03/013-1024x799.jpg)
LCDduino – Arduino Compatible 16×2 LCD module
The LCDduino board enables users to create many applications/projects that require a 16x2 LCD display and Arduino. The board has the exact size of 16x2 LCD and can be installed on the backside of the LCD. This is a low-cost solution that has onboard Arduino + LCD so no extra Arduino...
Continue Reading![4 Channel Analog Video Distribution Amplifier 4 Channel Analog Video Distribution Amplifier](https://www.electronics-lab.com/wp-content/uploads/2021/02/002-3-1024x976.jpg)
4 Channel Analog Video Distribution Amplifier
The project presented here is a low-cost video distribution amplifier capable of driving up to four video lines. The amplifier is configured with a non-inverting gain of 2. The input video source is terminated in 75 Ohms and is applied to the high impedance non-inverting input. Each...
Continue Reading