Tag: MOSFET
![Half Bridge with Single PWM Input Half Bridge with Single PWM Input](https://www.electronics-lab.com/wp-content/uploads/2024/06/13-1-1024x588.jpg)
Half Bridge with Single PWM Input
This is a Half-bridge module based on the LM5104 chip, which is a high-voltage gate driver. This High-Voltage Gate Driver is designed to drive both the high-side and the low-side N-channel MOSFETs in a synchronous buck configuration. The floating high-side driver can work with supply...
Continue Reading![Self-Oscillating Half Bridge Module Self-Oscillating Half Bridge Module](https://www.electronics-lab.com/wp-content/uploads/2024/06/17-1024x666.jpg)
Self-Oscillating Half Bridge Module
This is an automotive-grade self-oscillation 50% duty cycle half-bridge module built using the AUIR2085S chip from Infineon. The project consists of 2 x N-channel MOSFETs, and the module provides a primary side control solution to enable Half-Bridge DC-bus converters. The module is a...
Continue Reading![Lamp Flasher with Timer IC and MOSFET for Automotive Applications Lamp Flasher with Timer IC and MOSFET for Automotive Applications](https://www.electronics-lab.com/wp-content/uploads/2024/05/003-7-1024x487.jpg)
Lamp Flasher with Timer IC and MOSFET for Automotive Applications
This is a mini flasher board that can drive high-power LED or a lamp, mainly designed for automotive applications. The project consists BD9555FVM-C timer chip and MOSFET. The circuit is configured as a flasher, and can also be used as a PWM driver with an adjustable duty cycle and...
Continue Reading![2 Channel MOSFET Module 2 Channel MOSFET Module](https://www.electronics-lab.com/wp-content/uploads/2024/05/007-1024x594.jpg)
2 Channel MOSFET Module
This is a low profile and small size two-channel MOSFET board that can drive loads up to 2 x 3A. The Power Supply is 5V to 14V DC. Inputs and input Enable are TTL-level signals. The Output is by default enabled and an active high signal disables the output. Parallel Operation of Dual...
Continue Reading![H-Bridge for High Power Brushed DC Motor with Current Sense H-Bridge for High Power Brushed DC Motor with Current Sense](https://www.electronics-lab.com/wp-content/uploads/2024/01/006-8-1024x745.jpg)
H-Bridge for High Power Brushed DC Motor with Current Sense
This H-bridge board is an easy-to-use brushed DC motor driver that can handle large-size motors such as wheelchair motors, and winch motors. An H-bridge is an electronic circuit that switches the polarity of a voltage applied to a load. The circuit is built using 4 x N-Channel...
Continue Reading![Brushed DC Motor Speed Controller Using Radio Control (RC) Remote Brushed DC Motor Speed Controller Using Radio Control (RC) Remote](https://www.electronics-lab.com/wp-content/uploads/2023/05/003-9-1024x896.jpg)
Brushed DC Motor Speed Controller Using Radio Control (RC) Remote
This is a Brushed DC motor controller designed to control one brushed DC motor up to 5A. It can control the speed of the DC motor using a Radio Control (RC) System. This Arduino compatible hardware converts RC PWM signal into 0 to 100% duty cycle PWM which further drives high current...
Continue Reading![Electronic DC Load using TLE2141 Electronic DC Load using TLE2141](https://www.electronics-lab.com/wp-content/uploads/2023/04/002-3-1024x717.jpg)
Electronic DC Load using TLE2141
The circuit shown here is a low-cost electronic DC load designed to sink current from a power source. This test equipment can be used to test power devices such as power supplies, chargers, solar panels, and batteries. The board is built using op-amp TLE2141, LM385 provides the...
Continue Reading![Dual MOSFET Driver – Two Channel DC SSR Using MOSFETS & Gate Driver Dual MOSFET Driver – Two Channel DC SSR Using MOSFETS & Gate Driver](https://www.electronics-lab.com/wp-content/uploads/2022/06/005-2-1024x603.jpg)
Dual MOSFET Driver – Two Channel DC SSR Using MOSFETS & Gate Driver
The project presented here is a dual-channel MOSFET DC relay. The project is capable of driving a 5A load on each channel with an input supply of 48V DC. The LTC7067 chip drives the two high-side N-Channel MOSFETS with supply voltages up to 48V DC. Its powerful 0.8Ω pull-down and...
Continue Reading