Tag: MOSFET
![Low-Cost LED Dimmer using LM3578 Low-Cost LED Dimmer using LM3578](https://www.electronics-lab.com/wp-content/uploads/2022/06/006-2-1024x495.jpg)
Low-Cost LED Dimmer using LM3578
This Low-cost LED dimer project includes two main parts, an LM3578 chip, and a MOSFET. The LM3578 generates a PWM signal, and Q1 MOSFET helps to drive a high current LED. The project also includes current limit feature. Over current trigger point is set to 1.1A. LED intensity can be...
Continue Reading![Cooling Fan Controller Using Temperature Sensor LM35 Cooling Fan Controller Using Temperature Sensor LM35](https://www.electronics-lab.com/wp-content/uploads/2022/06/004-1024x634.jpg)
Cooling Fan Controller Using Temperature Sensor LM35
The project presented here is a low-cost solution for heat management of the heatsink and various equipment that requires automatic control of a cooling Fan. The project is built using a very cheap LM358 OPAMP. LM358 is used as a comparator, and a trimmer PR1 is provided to set the...
Continue Reading![1200V High-Current Half-Bridge using FAN73912 1200V High-Current Half-Bridge using FAN73912](https://www.electronics-lab.com/wp-content/uploads/2022/03/002-2-1024x845.jpg)
1200V High-Current Half-Bridge using FAN73912
The project presented here is designed for high-voltage and high-speed driving for MOSFETS and IGBTs that operate up to +1200V. The project consists of a FAN73912 gate driver chip and 2 x IGBTs, DC bus capacitors, current sense resistor for current feedback etc. The advanced input...
Continue Reading![High Current Half-Bridge with Over Current & Voltage Feedback for Step Down DC-DC Converter High Current Half-Bridge with Over Current & Voltage Feedback for Step Down DC-DC Converter](https://www.electronics-lab.com/wp-content/uploads/2022/03/001-1024x764.jpg)
High Current Half-Bridge with Over Current & Voltage Feedback for Step Down DC-DC Converter
This project enables the user to create a high current DC-DC converter. The project consists of a high current inductor, high current low voltage 2 x MOSFETs, half-bridge driver LT1158 chip, voltage feedback using onboard R9 and R10 resistor dividers, shunt resistor for overcurrent...
Continue Reading![High Current Half-Bridge with Over Current Shutdown High Current Half-Bridge with Over Current Shutdown](https://www.electronics-lab.com/wp-content/uploads/2022/02/001-2-1024x775.jpg)
High Current Half-Bridge with Over Current Shutdown
The project presented here is a versatile high voltage Half-Bridge with Over-Current Shutdown. The project is built using LT1158 IC from Analog Devices. It is suited for many applications as listed below. A single input pin on the LT1158 synchronously controls two N-channel power...
Continue Reading![High Current MOSFET Based Power Switch with Gate Driver High Current MOSFET Based Power Switch with Gate Driver](https://www.electronics-lab.com/wp-content/uploads/2022/02/005-1-1024x594.jpg)
High Current MOSFET Based Power Switch with Gate Driver
This power load switch project provides a simple and inexpensive method for power control. It is intended for driving a resistive or inductive load. A TTL logic signal from the system turns the load switch ON and OFF. The project consists of a low ohm N-Channel Power Trench MOSFET...
Continue Reading![PWM Temperature Controlled FAN using TC648 and NTC sensor PWM Temperature Controlled FAN using TC648 and NTC sensor](https://www.electronics-lab.com/wp-content/uploads/2022/01/SCH-8-1024x496.jpg)
PWM Temperature Controlled FAN using TC648 and NTC sensor
The project described here is a switch mode fan speed controller for use with brushed or brushless DC motors. Temperature proportional speed control is accomplished using pulse width modulation (PWM). 10K Ohms NTC is used to sense the temperature. The project is built using TC648 chip...
Continue Reading![Automatic LED Stairway Lighting – Arduino Compatible Automatic LED Stairway Lighting – Arduino Compatible](https://www.electronics-lab.com/wp-content/uploads/2021/05/005-1024x541.jpg)
Automatic LED Stairway Lighting – Arduino Compatible
This creative idea is suitable for a stairway with 16 stairs, each stair can have a 12V LED. It has two sensors one at the start and one at the end of the stairs and when the sensor trigered at any end it starts a process of lighting each of the steps in a progressive cycle starts....
Continue Reading