Tag: UART
![Sensirion SFA30-D-T is a formaldehyde detection module Sensirion SFA30-D-T is a formaldehyde detection module](https://www.electronics-lab.com/wp-content/uploads/2021/06/Screenshot-2021-06-20-at-14-17-16-Sensirion-SFA30-D-T-Environment-Sensor-20-To-50-°C-±20-ppb-Or-±20-Serial-7-Pin-Stacke....png)
Sensirion SFA30-D-T is a formaldehyde detection module
Formaldehyde Sensor Module for HVAC and Indoor Air Quality Applications SFA30 is a formaldehyde detection module based on electrochemical sensing technology optimized for lowest false alarm rates. The SFA30 HCHO sensor has alow cross-sensitivity to ethanol and is optimized to operate...
Continue Reading![Discovery series logic analyzer offer 1GS/s speed on all 16-channels Discovery series logic analyzer offer 1GS/s speed on all 16-channels](https://www.electronics-lab.com/wp-content/uploads/2021/06/Logic-Analyser.png)
Discovery series logic analyzer offer 1GS/s speed on all 16-channels
We have already seen several logic analyzers, but an Indian startup, Prodigy Technovations, the leading provider of innovative protocol analysis solutions, has launched a Logic Analyzer for Embedded Interfaces. The Discovery series logic analyzer, also identified as PGY-LA-EMBD, offers...
Continue Reading![BIGTREETECH SKR MINI E3 V2.0 32 Bit Control Board for the Ender3 Printers BIGTREETECH SKR MINI E3 V2.0 32 Bit Control Board for the Ender3 Printers](https://www.electronics-lab.com/wp-content/uploads/2021/05/bigtreetech-product-display.png)
BIGTREETECH SKR MINI E3 V2.0 32 Bit Control Board for the Ender3 Printers
3D printer controller boards are the brains of any 3D printer. All the electrical components are interfaced with the printer motherboard. The main job of the controller is to follow the code from the 3D printer software and produce a 3D printed object. The controller receives various...
Continue Reading![An Introduction: LCD Common Interfaces An Introduction: LCD Common Interfaces](https://www.electronics-lab.com/wp-content/uploads/2020/12/1.png)
An Introduction: LCD Common Interfaces
There are a lot of different LCD display interfaces depending on the requirements of resolutions, speed, cost, stability etc. The following outlines the common ones on the market: Parallel vs Serial Interface Parallel interface could transmit many data bits at the same time...
Continue Reading![Isolated, Single-Channel RS232 transceiver (Isolated RS232 to UART) Isolated, Single-Channel RS232 transceiver (Isolated RS232 to UART)](https://www.electronics-lab.com/wp-content/uploads/2020/12/111111111-e1609183857720.jpg)
Isolated, Single-Channel RS232 transceiver (Isolated RS232 to UART)
The project presented here provides an isolated interface between the RS-232 cable network and the connected UART systems to protect against voltage spikes and ground loops within the noisy environment and improve system reliability. The project achieves a robust data communication link...
Continue Reading![A full-duplex tiny AVR software UART A full-duplex tiny AVR software UART](https://www.electronics-lab.com/wp-content/uploads/2020/09/AVR-timer-counter.png)
A full-duplex tiny AVR software UART
UARTs for AVR MCUs by Nerd Ralph, he writes: I’ve written a few software UARTs for AVR MCUs. All of them have bit-banged the output, using cycle-counted assembler busy loops to time the output of each bit. The code requires interrupts to be disabled to ensure accurate timing between...
Continue Reading![Cricket ONE is an Arduino compatible board in Raspberry Pi form factor Cricket ONE is an Arduino compatible board in Raspberry Pi form factor](https://www.electronics-lab.com/wp-content/uploads/2020/05/image-2.png)
Cricket ONE is an Arduino compatible board in Raspberry Pi form factor
The Cricket ONE is the first in a series of small microcontroller boards using the familiar form factor of the Raspberry Pi Zero series of single-board computers. Featuring an ATMEGA328PB and CH340C USB to UART converter, this board is Arduino IDE compatible and includes all of the...
Continue Reading![Already Compact Arduino Nano Scaled-Down Into a Breadboard Friendly Chip Already Compact Arduino Nano Scaled-Down Into a Breadboard Friendly Chip](https://www.electronics-lab.com/wp-content/uploads/2020/04/Dily3217-Scales-Down-an-Arduino-Nano-Into-a-Breadboard-Friendly-Chip-Hackster.io_.png)
Already Compact Arduino Nano Scaled-Down Into a Breadboard Friendly Chip
The new Dily3217 is a breadboard friendly Arduino compatible development board that is easy to integrate with more or less the same functionality as the Nano. Powered by a very small Atmel AVR chip, the Dily3217 copies virtually all the features of the already compact Arduino Nano into...
Continue Reading